Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM (for Sedan)

DTC    C1407    Open or Short in Rear Speed Sensor RH Circuit

DTC    C1408    Open or Short in Rear Speed Sensor LH Circuit

for Preparation Click here


DESCRIPTION

Refer to DTCs C1403 and C1404 (Click here).

DTC NO.
DTC Detection Condition
Trouble Area
C1407
C1408
Either of the following is detected:
  1. An open in the speed sensor signal circuit continues for 0.5 seconds or more.
  2. With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.
  1. Rear axle hub and bearing assembly RH/LH
    (rear speed sensor, speed sensor rotor)
  2. Skid control sensor wire
  3. Harness or connector
  4. Brake actuator assembly (skid control ECU)

HINT:
  1. DTC C1407 is for the rear speed sensor RH.
  2. DTC C1408 is for the rear speed sensor LH.


WIRING DIAGRAM


C239922E04


INSPECTION PROCEDURE

NOTICE:
  1. Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited.
  2. Check the speed sensor signal after replacement (Click here).

1.READ VALUE USING INTELLIGENT TESTER (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Speed Open
    RR speed sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    RL Speed Open
    RL speed sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -

    OK:
    There are no momentary interruptions.

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 4
OK


2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Vehicle stopped:
    0 km/h
    When driving at constant speed: No large fluctuations
    RL Wheel Speed
    RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Vehicle stopped:
    0 km/h
    When driving at constant speed: No large fluctuations

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
Go to step 4
OK


3.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTCs (C1407 and C1408) are not output
    A
    DTCs (C1407 and/or C1408) are output
    B

HINT:
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

4.INSPECT SKID CONTROL SENSOR WIRE
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control sensor wire.



    C237298E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    RH 
    Tester Connection
    Condition
    Specified Condition
    Z1-2 - ZJ3-1
    Always
    Below 1 Ω
    Z1-1 - ZJ3-2
    Always
    Below 1 Ω
    Z1-2 - ZJ3-2
    Always
    10 kΩ or higher
    Z1-2 - Body ground
    Always
    10 kΩ or higher
    Z1-1 - ZJ3-1
    Always
    10 kΩ or higher
    Z1-1 - Body ground
    Always
    10 kΩ or higher
    LH 
    Tester Connection
    Condition
    Specified Condition
    a1-2 - aJ3-1
    Always
    Below 1 Ω
    a1-1 - aJ3-2
    Always
    Below 1 Ω
    a1-2 - aJ3-2
    Always
    10 kΩ or higher
    a1-2 - Body ground
    Always
    10 kΩ or higher
    a1-1 - aJ3-1
    Always
    10 kΩ or higher
    a1-1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Skid Control Sensor Wire
    *a
    RH
    *b
    LH

  1. Reconnect the rear speed sensor wire.



NG
REPLACE SKID CONTROL SENSOR WIRE
OK


5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the A76 brake actuator assembly (skid control ECU) connector and the Z1 and/or a1 rear speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A76-17 (RR+) - Z1-2
    Always
    Below 1 Ω
    A76-16 (RR-) - Z1-1
    Always
    Below 1 Ω
    A76-5 (RL+) - a1-2
    Always
    Below 1 Ω
    A76-4 (RL-) - a1-1
    Always
    Below 1 Ω
    A76-17 (RR+) - Body ground
    Always
    10 kΩ or higher
    A76-16 (RR-) - Body ground
    Always
    10 kΩ or higher
    A76-5 (RL+) - Body ground
    Always
    10 kΩ or higher
    A76-4 (RL-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the A76 brake actuator assembly (skid control ECU) connector and the rear speed sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)


    C234065E08
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    RH:
    Tester Connection
    Switch Condition
    Specified Condition
    Z1-2 - Body ground
    Ignition switch ON
    8 to 14 V
    LH:
    Tester Connection
    Switch Condition
    Specified Condition
    a1-2 - Body ground
    Ignition switch ON
    8 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Speed Sensor)
    *b
    RH
    *c
    LH

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).

  1. Reconnect the Z1 and/or a1 rear speed sensor connector.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (Click here)