DTC P0110 Intake Air Temperature Circuit Malfunction |
DTC P0112 Intake Air Temperature Circuit Low Input |
DTC P0113 Intake Air Temperature Circuit High Input |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0110 | Open or short in intake air temperature circuit for 0.5 seconds (1 trip detection logic) |
|
| P0112 | Short in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0113 | Open in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| Temperature Displayed | Malfunction |
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) | Short circuit |
| Frequency of Operation | Continuous |
| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the tester.
| Result | Proceed to |
| -40°C (-40°F) | A |
| 140°C (284°F) | B |
| Same as actual intake air temperature | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
Check the connection and terminal contact pressure of connectors and wire harness between the mass air flow meter and ECM.
![]() |
Disconnect the mass air flow meter connector.
Connect terminals 4 (THA) and 5 (E2) of the mass air flow meter wire harness side connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the tester.
| *1 | Mass air flow meter |
| *2 | ECM |
| *a | Front view of wire harness connector (to Mass Air Flow Meter) |
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B72-4 (THA) - B84-65 (THA) | Always | Below 1 Ω |
| B72-5 (E2) - B84-88 (ETHA) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
![]() |
Disconnect the mass air flow meter connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the tester.
| *1 | Mass Air Flow Meter |
| *2 | ECM |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B72-4 (THA) or B84-65 (THA) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||