DTC P2111 Throttle Actuator Control System - Stuck Open |
DTC P2112 Throttle Actuator Control System - Stuck Closed |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2111 | ECM signals throttle actuator to close, but the actuator is stuck (1 trip detection logic) |
|
| P2112 | ECM signals throttle actuator to open, but the actuator is stuck (1 trip detection logic) |
|
| Required Sensors/Components | Throttle with motor body assembly |
| Frequency of Operation | Continuous |
| Throttle actuator | ON |
| Throttle actuator duty calculation | Executing |
| Throttle position sensor fail | Not detected |
| Throttle actuator current-cut operation | Not executing |
| Throttle actuator power supply | 4 V or higher |
| Throttle actuator fail | Not detected |
| All of following conditions met | - |
| Throttle actuator current | 2 A or higher |
| Duty cycle to close throttle | 80% or more |
| All of following conditions met | - |
| Throttle actuator current | 2 A or higher |
| Duty cycle to open throttle | 80% or more |
| Throttle position sensor voltage | No change |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2111 OR P2112) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| P2111 or P2112 is output | A |
| P2111 or P2112 and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE) |
Check for foreign objects between the throttle valve and the housing. If necessary, clean the throttle with motor body assembly. Then check that the throttle valve moves smoothly.
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.
Read the values displayed on the tester while wiggling the ECM wire harness.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| Value in Data List changes when wire harness is wiggled, or DTC is output | A |
| Other than above | B |
|
| ||||
| A | |
| 4.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE WITH MOTOR BODY ASSEMBLY) |
As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (Click here).
| NEXT | ||
| ||
| 5.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY |
Replace the throttle with motor body assembly (Click here).
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the tester on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P2111 or P2112 is output | B |
|
| ||||
| A | ||
| ||