Home › Engine / Hybrid System · 1NZ-FE › ENGINE CONTROL › 1NZ-FE SFI SYSTEM

DTC    P2120    Throttle / Pedal Position Sensor / Switch "D" Circuit

DTC    P2122    Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input

DTC    P2123    Throttle / Pedal Position Sensor / Switch "D" Circuit High Input

DTC    P2125    Throttle / Pedal Position Sensor / Switch "E" Circuit

DTC    P2127    Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input

DTC    P2128    Throttle / Pedal Position Sensor / Switch "E" Circuit High Input

DTC    P2138    Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation

for Preparation Click here


DESCRIPTION

HINT:
  1. This electronic throttle control system does not use a throttle cable.
  2. These DTCs relate to the accelerator pedal position sensor.

The accelerator pedal position sensor is mounted on the accelerator pedal bracket and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type and uses Hall-effect elements in order to yield accurate signals even in extreme conditions. The voltage from this sensor, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal operating angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.
The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

A256706E03


DTC No.
DTC Detection Condition
Trouble Area
P2120
VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more
(1 trip detection logic)
  1. Accelerator pedal sensor assembly
  2. ECM
P2122
VPA is 0.4 V or less for 0.5 seconds or more when accelerator pedal depressed
(1 trip detection logic)
  1. Accelerator pedal sensor assembly
  2. Open in VCPA circuit
  3. Open or ground short in VPA circuit
  4. ECM
P2123
VPA is 4.8 V or more for 2.0 seconds or more
(1 trip detection logic)
  1. Accelerator pedal sensor assembly
  2. Open in EPA circuit
  3. ECM
P2125
VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more
(1 trip detection logic)
  1. Accelerator pedal sensor assembly
  2. ECM
P2127
VPA2 is 1.2 V or less for 0.5 seconds or more when accelerator pedal is depressed
(1 trip detection logic)
  1. Accelerator pedal sensor assembly
  2. Open in VCP2 circuit
  3. Open or ground short in VPA2 circuit
  4. ECM
P2128
Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or more
(b) VPA is between 0.4 V and 3.45 V
  1. Accelerator pedal sensor assembly
  2. Open in EPA2 circuit
  3. ECM
P2138
Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic):
(a) Difference between VPA and VPA2 is 0.02 V or less
(b) VPA is 0.4 V or less and VPA2 is 1.2 V or less
  1. Short between VPA and VPA2 circuits
  2. Accelerator pedal sensor assembly
  3. ECM

HINT:
When any of these DTCs are stored, check the accelerator pedal position sensor voltage by entering the following menus using the intelligent tester: Powertrain / Engine and ECT / Data List / Accel Sensor Out No.1 and Accel Sensor Out No.2.

Trouble Area
Accelerator Pedal Released
Accelerator Pedal Depressed
Accel Sensor Out No. 1
Accel Sensor Out No. 2
Accel Sensor Out No. 1
Accel Sensor Out No. 2
Open in VCP circuit
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
Open or ground short in VPA circuit
0 to 0.2 V
1.2 to 2.0 V
0 to 0.2 V
3.4 to 4.7 V
Open or ground short in VPA2 circuit
0.5 to 1.1 V
0 to 0.2 V
2.6 to 4.5 V
0 to 0.2 V
Open in EPA circuit
4.5 to 4.98 V
4.5 to 4.98 V
4.5 to 4.98 V
4.5 to 4.98 V
Normal condition
0.5 to 1.1 V
1.2 to 2.0 V
2.6 to 4.5 V
3.4 to 4.7 V

HINT:
Accelerator pedal positions are expressed as voltages.


MONITOR DESCRIPTION

When the output voltage of either VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits is less than the threshold, the ECM determines that there is a malfunction in the accelerator pedal position sensor. The ECM then illuminates the MIL and stores a DTC.
Example:
When the output voltage of VPA drops below 0.4 V for more than 0.5 seconds when the accelerator pedal is fully depressed, DTC P2122 is stored.

MONITOR STRATEGY


Required Sensors/Components
Accelerator pedal position sensor
Frequency of Operation
Continuous

COMPONENT OPERATING RANGE


VPA voltage
0.5 V to 4.5 V
VPA2 voltage
1.2 V to 4.7 V
Difference between VPA and VPA2 voltages
more than 0.05 V

CONFIRMATION DRIVING PATTERN


A199317E01

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on [A].
  6. Fully depress and release the accelerator pedal [B].
  7. Check that 5 seconds or more have elapsed since the ignition switch was turned to ON.
  8. Enter the following menus: Powertrain / Engine and ECT / DTC [C].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P2120, P2122, P2123, P2125, P2127, P2128 or P2138.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again.


FAIL-SAFE

When any of DTCs P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138 are stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM


A254093E01


INSPECTION PROCEDURE

HINT:
  1. These DTCs relate to the accelerator pedal position sensor.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION SENSOR)
A160308E03
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

  1. Read the values displayed on the tester.

    Standard Voltage:
    Accelerator Pedal Operation
    Accel Sensor Out No. 1
    Accel Sensor Out No. 2
    Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2
    Released
    0.5 to 1.1 V
    1.2 to 2.0 V
    More than 0.02 V
    Depressed
    2.6 to 4.5 V
    3.4 to 4.7 V

    Text in Illustration 
    *a
    Accelerator Pedal
    *b
    Depressed
    *c
    Released

Result 
Result
Proceed to
NG
A
OK
B


B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A36-6 (VPA) - A74-55 (VPA)
    Always
    Below 1 Ω
    A36-5 (EPA) - A74-59 (EPA)
    Always
    Below 1 Ω
    A36-4 (VCPA) - A74-57 (VCPA)
    Always
    Below 1 Ω
    A36-3 (VPA2) - A74-56 (VPA2)
    Always
    Below 1 Ω
    A36-2 (EPA2) - A74-60 (EPA2)
    Always
    Below 1 Ω
    A36-1 (VCP2) - A74-58 (VCP2)
    Always
    Below 1 Ω
    A36-6 (VPA) or A74-55 (VPA) - Body ground
    Always
    10 kΩ or higher
    A36-5 (EPA) or A74-59 (EPA) - Body ground
    Always
    10 kΩ or higher
    A36-4 (VCPA) or A74-57 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A36-3 (VPA2) or A74-56 (VPA2) - Body ground
    Always
    10 kΩ or higher
    A36-2 (EPA2) or A74-60 (EPA2) - Body ground
    Always
    10 kΩ or higher
    A36-1 (VCP2) or A74-58 (VCP2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (VCPA AND VCP2 VOLTAGE)


    A254580E06
  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A36-4 (VCPA) - A36-5 (EPA)
    Ignition switch ON
    4.5 to 5.5 V
    A36-1 (VCP2) - A36-2 (EPA2)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Accelerator Pedal Sensor Assembly)



NG
REPLACE ECM (Click here)
OK


4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
  1. Replace the accelerator pedal sensor assembly (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Fully depress and release the accelerator pedal.

  1. Check that 5 seconds or more have elapsed since the ignition switch was turned to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 are output
    A
    DTC is not output
    B



B
END
A

REPLACE ECM (Click here)