QUARTER WINDOW GLASS > INSTALLATION |
| 1. CLEAN QUARTER WINDOW GLASS |
![]() |
Using a scraper, remove the adhesive sticking to the quarter window glass.
Clean the outer edge of the quarter window glass with a non-residue solvent.
| 2. INSTALL QUARTER WINDOW GLASS SPACER |
Using a brush or sponge, coat the application area of the quarter window glass spacer with Primer G.
![]() |
Install 2 new quarter window glass spacers onto the glass, as shown in the illustration.
| *a | Back Side |
| 3. INSTALL QUARTER WINDOW CLIP |
Using a brush or sponge, coat the application area of the quarter window clip with Primer G.
![]() |
Install 3 new quarter window clips onto the quarter window glass, as shown in the illustration.
| *a | Back Side |
| 4. INSTALL QUARTER WINDOW MOULDING |
Using a brush or sponge, coat the application area of the quarter window moulding with Primer G.
![]() |
Install new quarter window moulding onto the quarter window glass, as shown in the illustration.
| *a | 9.5 mm (0.374 in.) |
| 5. INSTALL QUARTER WINDOW GLASS |
![]() |
Clean and shape the contact surface of the vehicle body.
| *1 | Adhesive |
Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.
Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.
![]() |
Position the quarter window glass.
| *a | Mark |
Using suction cups, place the quarter window glass in the correct position.
Check that the whole contact surface of the quarter window glass rim is perfectly even.
Align the matchmarks on the quarter window glass and vehicle body.
Remove the quarter window glass.
![]() |
Using a brush, coat the installation surface on the vehicle body with Primer M.
| *1 | Primer M |
| *2 | Adhesive |
| *a | Correct |
| *b | Incorrect |
Using a brush or sponge, coat the application areas that still have adhesive attached with Primer G.

| *1 | Primer G | - | - |
| *a | Back Side | *b | 6.4 mm (0.252 in.) |
| *c | 14.0 mm (0.551 in.) | *d | 8.3 mm (0.327 in.) |
| *e | 22.0 mm (0.866 in.) | *f | 6.0 mm (0.236 in.) |
| *g | 6.5 mm (0.256 in.) | - | - |
Apply adhesive to the glass.
Cut the tip off the cartridge nozzle.
| Temperature | Usage Time Frame |
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply adhesive to the quarter window glass, as shown in the illustration.

| *1 | Adhesive | - | - |
| *a | Back Side | *b | 8.0 mm (0.315 in.) |
| *c | 12.0 mm (0.472 in.) | *d | 13.4 mm (0.528 in.) |
| *e | 23.3 mm (0.917 in.) | *f | 15.3 mm (0.602 in.) |
| *g | 13.0 mm (0.512 in.) | *h | 13.5 mm (0.531 in.) |
Install the quarter window glass.
![]() |
Using suction cups, position the quarter window glass so that the matchmarks are aligned, and press it in gently along the rim.
| *a | Mark |
Hold the quarter window glass in place securely with protective tape or the equivalent until the adhesive hardens.
Lightly press the front surface of the glass to ensure a close fit.
![]() |
If necessary, use a scraper to correct the level or position of adhesive that has been applied.
| *1 | Quarter Window Glass |
| *2 | Dam |
| *3 | Adhesive |
| Temperature | Minimum Time Prior to Driving Vehicle |
| 35°C (95°F) | 1 hour and 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
| 6. INSPECT FOR LEAK AND REPAIR |
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
| 7. INSTALL REAR ROOF SIDE RAIL GARNISH |
| 8. INSTALL ROOF SIDE INNER GARNISH |
| 9. INSTALL DECK TRIM SIDE PANEL ASSEMBLY |
| 10. INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY |
| 11. INSTALL REAR FLOOR FINISH PLATE |
Engage the 4 guides and the 4 claws to install the rear floor finish plate.
| 12. INSTALL JACK HANDLE (for RH Side) |
| 13. INSTALL NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light) |
Connect the connector.
![]() |
Engage the claw to install the No. 2 room light assembly.
| 14. INSTALL CENTER PILLAR UPPER GARNISH |
| 15. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY |
| 16. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY |
| 17. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP |
| 18. INSTALL FRONT DOOR SCUFF PLATE |
| 19. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side) |
| 20. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side) |
| 21. INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type) |
| 22. INSTALL SPARE WHEEL COVER |
Install the spare wheel cover.
| 23. INSTALL DECK BOARD ASSEMBLY |
Install the deck board.