Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS

QUARTER WINDOW GLASS > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.



1. REMOVE DECK BOARD ASSEMBLY


    B272608
  1. Remove the deck board.



2. REMOVE SPARE WHEEL COVER


    B272609
  1. Remove the spare wheel cover.



3. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
(Click here)


4. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
(Click here)


5. REMOVE REAR SEAT ASSEMBLY (for Fold Down Seat Type)
(Click here)


6. REMOVE FRONT DOOR SCUFF PLATE

HINT:
Use the same procedure as for the RH side .



7. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP

HINT:
Use the same procedure as for the RH side .



8. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY

HINT:
Use the same procedure as for the RH side .



9. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY

HINT:
Use the same procedure as for the RH side .



10. REMOVE CENTER PILLAR UPPER GARNISH

HINT:
Use the same procedure as for the RH side .



11. REMOVE NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)


    E222045E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw.
    Text in Illustration 
    *1
    Protective Tape

  1. Disconnect the connector and remove the No. 2 room light assembly.



12. REMOVE JACK HANDLE (for RH Side)


13. REMOVE REAR FLOOR FINISH PLATE


    B272624
  1. Disengage the 4 claws and 4 guides and remove the rear floor finish plate.



14. SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY

HINT:
Use the same procedure as for the RH side .



15. REMOVE DECK TRIM SIDE PANEL ASSEMBLY

HINT:
Use the same procedure as for the RH side .



16. REMOVE ROOF SIDE INNER GARNISH

HINT:
Use the same procedure as for the RH side .



17. REMOVE REAR ROOF SIDE RAIL GARNISH

HINT:
Use the same procedure as for the RH side .



18. REMOVE QUARTER WINDOW MOULDING


    B116961E02
  1. Using a knife, cut off the quarter window moulding, as shown in the illustration.
    Text in Illustration 
    *a
    Cut

    NOTICE:
    Do not damage the vehicle body with the knife.

    HINT:
    Make a partial cut in the quarter window moulding. Then pull and remove it by hand.



19. REMOVE QUARTER WINDOW GLASS


    B284420E01
  1. Apply protective tape to the installation area on the quarter window glass on the vehicle body.
    Text in Illustration 
    *1
    Protective Tape



    B284421E01
  1. Place matchmarks on the quarter window glass and vehicle body on the locations indicated in the illustration.
    Text in Illustration 
    *a
    Mark

    HINT:
    Matchmarks do not need to be placed if the quarter window glass is not going to be reused.



    B284422E01
  1. Pass a piano wire between the vehicle body and glass from the interior.
    Text in Illustration 
    *1
    Piano Wire

  1. Tie both wire ends to wooden blocks or similar objects.

  1. Cut through the adhesive by pulling the piano wire around the quarter window glass.

    NOTICE:
    When separating the quarter window glass, take care not to damage the paint or the interior and exterior ornaments.



    B284423
  1. Using suction cups, disengage the 3 clips and remove the quarter window glass.



20. REMOVE QUARTER WINDOW CLIP
  1. Using a scraper, remove the 3 quarter window clips.

    NOTICE:
    Be sure to replace the quarter window clip with a new one.



21. REMOVE QUARTER WINDOW GLASS SPACER
  1. Using a scraper, remove the 2 quarter window glass spacers.

    NOTICE:
    Be sure to replace the quarter window glass spacer with a new one.