Home › Engine / Hybrid System · 2NZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0617    Starter Relay Circuit High

for Preparation Click here


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No.
DTC Detection Condition
Trouble Area
P0617
Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):
  1. (a) Vehicle speed is 20 km/h (12.4 mph) or more.
  2. (b) Engine speed is 1000 rpm or more.
  3. (c) STA signal is on.
  1. Park/neutral position switch assembly*1
  2. Clutch start switch assembly*2
  3. Starter relay (ST) circuit
  4. Ignition switch assembly
  5. ECM
*1: for Automatic Transaxle
*2: for Manual Transaxle

MONITOR STRATEGY


Required Sensors/Components (Main)
Starter relay, Park/neutral position switch assembly, Clutch start switch assembly and Ignition switch
Required Sensors/Components (Related)
Vehicle speed sensor, Crankshaft position sensor
Frequency of Operation
Continuous

TYPICAL ENABLING CONDITIONS


Vehicle speed
20 km/h (12.4 mph) or more
Engine speed
1000 rpm or more

TYPICAL MALFUNCTION THRESHOLDS


Starter signal
ON

CONFIRMATION DRIVING PATTERN


A231469E04

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on [A].
  6. Idle the engine for 5 seconds or more [B].
  7. Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Enter the following menus: Powertrain / Engine and ECT / DTC [D].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0617.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.


WIRING DIAGRAM

Refer to DTC Starter Signal Circuit .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine can be cranked normally.
    If the engine does not crank, proceed to Problem Symptoms Table (Click here).
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to ON and START.

    OK:

    Ignition Switch Position
    Tester Display
    ON
    OFF
    START
    ON


    Result 
    Result
    Proceed to
    OK
    A
    NG
    (for Automatic Transaxle)
    B
    NG
    (for Manual Transaxle)
    C



B
Go to step 2

C
Go to step 6
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Disconnect the park/neutral position switch assembly connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is turned to ON.

    Result 
    Result
    Proceed to
    Remains ON
    A
    OFF
    B



B
Go to step 4
A


3.INSPECT ECM (STA TERMINAL VOLTAGE)


    A200912E17
  1. Disconnect the park/neutral position switch assembly connector.

  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

Text in Illustration 
*a
Front view of wire harness connector
(to ECM)

Result 
Tester Connection
Switch Condition
Specified Condition
Proceed to
A74-48 (STA) - Body ground
Ignition switch ON
11 to 14 V
A
Below 1.5 V
B


B
REPLACE ECM (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY - ECM) 

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    A107908E91
  1. Disconnect the park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (B) - 5 (L)
    Shift lever in any position other than P or N
    10 kΩ or higher
    2 (RB) - 5 (L)
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Park/Neutral Position Switch Assembly)
    Result 
    Result
    Proceed to
    Short between 4 (B) and 5 (L)
    A
    Short between 2 (RB) and 5 (L)
    B
    Within standard range
    C



B
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

C
Go to step 10
A


5.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Replace the park/neutral position switch assembly (Click here).



NEXT
Go to step 10

6.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Disconnect the clutch start switch assembly connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is turned to ON.

    Result 
    Result
    Proceed to
    Remains ON
    A
    OFF
    B



B
Go to step 8
A


7.INSPECT ECM (STA TERMINAL SIGNAL)


    A200912E17
  1. Disconnect the clutch start switch assembly connector.

  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

Text in Illustration 
*a
Front view of wire harness connector
(to ECM)

Result 
Tester Connection
Switch Condition
Specified Condition
Proceed to
A74-48 (STA) - Body ground
Ignition switch ON
11 to 14 V
A
Below 1.5 V
B


B
REPLACE ECM (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST RELAY - ECM) 

8.INSPECT CLUTCH START SWITCH ASSEMBLY
  1. Inspect the clutch start switch assembly (Click here).

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 10
A


9.REPLACE CLUTCH START SWITCH ASSEMBLY
  1. Replace the clutch start switch assembly (Click here).


NEXT


10.INSPECT IGNITION SWITCH ASSEMBLY
  1. Inspect the ignition switch assembly (Click here).



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK


11.INSPECT ECM (NSW TERMINAL VOLTAGE)


    A257481E01
  1. Disconnect the park/neutral position switch assembly*1 or clutch start switch*2 connector.
    *1: for Automatic Transaxle
    *2: for Manual Transaxle

  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

Text in Illustration 
*a
Front view of wire harness connector
(to ECM)

Result 
Tester Connection
Switch Condition
Specified Condition
Proceed to
B84-52 (NSW) - Body ground
Ignition switch ON
11 to 14 V
A
(for automatic transaxle)
B
(for manual transaxle)
Below 1.5 V
C


B
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH - ECM)

C
REPLACE ECM (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)