Home › Engine / Hybrid System · 2NZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0130    Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 1)

DTC    P0132    Oxygen Sensor Circuit High Voltage Bank1 Sensor1

DTC    P2195    Oxygen Sensor Signal Stuck Lean (Bank 1 Sensor 1)

DTC    P2196    Oxygen Sensor Signal Stuck Rich (Bank 1 Sensor 1)

for Preparation Click here


DESCRIPTION

Refer to P0031 .

HINT:
Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DTC No.
DTC Detection Condition
Trouble Area
P0130
Voltage output of heated oxygen sensor remains at 0.4 V or more, and 0.5 V or less, during idling with warm engine (2 trip detection logic)
  1. Open or short in heated oxygen sensor (sensor 1) circuit
  2. Heated oxygen sensor (sensor 1)
  3. No. 1 integration relay (EFI MAIN relay)
  4. Intake system
  5. Fuel pressure
  6. Fuel injector assembly
  7. ECM
P0132
Heated oxygen sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip detection logic)
  1. Short in heated oxygen sensor (sensor 1) circuit
  2. Heated oxygen sensor
  3. ECM internal circuit malfunction
P2195
Output voltage of heated oxygen sensor remains at 0.5 V or less during idling with warm engine (2 trip detection logic)
  1. Open or short in heated oxygen sensor (sensor 1) circuit
  2. Heated oxygen sensor (sensor 1)
  3. No. 1 integration relay (EFI MAIN relay)
  4. Intake system
  5. Fuel pressure
  6. Fuel injector assembly
  7. ECM
P2196
Output voltage of heated oxygen sensor remains at 0.4 V or more during idling with warm engine (2 trip detection logic)
  1. Open or short in heated oxygen sensor (sensor 1) circuit
  2. Heated oxygen sensor (sensor 1)
  3. No. 1 integration relay (EFI MAIN relay)
  4. Intake system
  5. Fuel pressure
  6. Fuel injector assembly
  7. ECM

MONITOR DESCRIPTION


A106749E04

The ECM uses the heated oxygen sensor information to regulate the air-fuel ratio close to a stoichiometric air-fuel ratio. This maximizes the catalytic converter's ability to purify the exhaust gases. The heated oxygen sensor detects oxygen levels in the exhaust gas and sends this signal to the ECM.
The inner surface of the sensor element is exposed to outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and an integrated heating element. The heated oxygen sensor's output voltage changes suddenly in the vicinity of the stoichiometric air-fuel ratio. The heated oxygen sensor generates output voltage between 0 V and 1 V in response to the oxygen concentration in the exhaust gas. When the front heated oxygen sensor voltage is 0.45 V or more, the ECM judges that the air-fuel ratio is rich. When it is 0.45 V or less, the ECM judges that the air-fuel ratio is lean.
  1. The heated oxygen sensor should indicate rich and lean alternately at a regular cycle under the air-fuel ratio feedback control. If the heated oxygen sensor voltage remains at rich or lean for about 23 seconds (x 3 times), the ECM interprets this as a malfunction of the heated oxygen sensor, illuminates the MIL (2 trip detection logic) and stores DTC P0130, 2195 or 2196.
  2. If the front heated oxygen sensor output voltage exceeds 1.2 V for 10 seconds, the ECM illuminates the MIL (2 trip detection logic) and stores DTC P0132.

MONITOR STRATEGY


Required Sensors/Components (Main)
Heated oxygen sensor (sensor 1)
Required Sensors/Components (Related)
Crankshaft position sensor, Vehicle speed sensor
Frequency of Operation
Once per driving cycle

TYPICAL ENABLING CONDITIONS


Time after engine start
120 seconds
Idling
ON
Fuel system status
Closed loop
Vehicle speed
Less than 5 km/h
Driving record for 20 seconds or more
40 km/h (25 mph) or more and 900 rpm or more

TYPICAL MALFUNCTION THRESHOLDS


Heated oxygen sensor voltage (P0130): 
Occasions either of following conditions is met
More than 3 times
Minimum heated oxygen sensor voltage
0.4 V or more for 23 seconds or more
Maximum heated oxygen sensor voltage
0.5 V or less for 23 seconds or more

Heated oxygen sensor out of range (P0132) 
Heated oxygen sensor voltage
1.2 V or more

Heated oxygen sensor voltage stuck Lean (P2195) 
Occasions following condition is met
2 times
Maximum heated oxygen sensor voltage
0.5 V or less for 23 seconds or more

heated oxygen sensor voltage stuck Rich (P2196) 
Occasions following condition is met
2 times
Minimum heated oxygen sensor voltage
0.4 V or more for 23 seconds or more

COMPONENT OPERATING RANGE


Heated oxygen sensor voltage
Fluctuates for a second

CONFIRMATION DRIVING PATTERN


A219223E07

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on [A].
  6. Start the engine and idle it for 120 seconds or more [B].
  7. Drive the vehicle at 40 km/h (25 mph) or more for 20 seconds [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Idle the engine for 30 seconds or more [D].
  9. Perform step [C] and [D] at least 3 times.
  10. Idle the engine for 40 seconds or more [E].
  11. Enter the following menus: Powertrain / Engine / DTC [F].
  12. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  13. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  14. Input the DTC: P0130, P0132, P2195 or P2196.
  15. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [F].


WIRING DIAGRAM

Refer to P0031

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume function provided in the Active Test. The Control the Injection Volume function can help to determine whether the heated oxygen sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester on.
  3. Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
  5. Perform the Active Test operation with the engine idling.
  6. Monitor the output voltages of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the tester.

HINT:
  1. Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Tester Display
(Sensor)
Injection Volume
Status
Voltage
O2S B1S1
(Heated oxygen sensor (sensor 1))
+12%
Rich
Higher than 0.5 V
-12%
Lean
Below 0.4 V
O2S B1S2
(Heated oxygen sensor (sensor 2))
+12%
Rich
Higher than 0.5 V
-12%
Lean
Below 0.4 V

NOTICE:
The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.


Case
Heated Oxygen Sensor (Sensor 1) Output Voltage
Heated Oxygen Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E05
A150789E07
A150787E05
A150788E09
-
2
A150787E05
A150790E01
A150787E05
A150788E09
  1. Heated oxygen sensor (Sensor 1)
  2. Heated oxygen sensor heater (Sensor 1)
  3. Heated oxygen sensor circuit (Sensor 1)
3
A150787E05
A150789E07
A150787E05
A150790E01
  1. Heated oxygen sensor (Sensor 2)
  2. Heated oxygen sensor heater (Sensor 2)
  3. Heated oxygen sensor circuit (Sensor 2)
4
A150787E05
A150790E01
A150787E05
A150790E01
  1. Fuel injector assembly
  2. Fuel pressure
  3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)

HINT:
  1. Following the Control the Injection Volume procedure enables technicians to check and graph the voltage outputs of both heated oxygen sensors
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / O2S B1S1 and O2S B1S2, then press the view button.

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0130, P0132, P2195 AND/OR P2196)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P0130, P2195 and/or P2196 are output
    A
    DTC P0130, P0132, P2195 and/or P2196 and other DTCs are output
    B
    DTC P0132 is output
    C

    HINT:
    If any DTCs other than P0130, P0132, P2195 and/or P2196 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)

C
Go to step 10
A


2.READ VALUE USING INTELLIGENT TESTER (O2S B1S1)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S1.

  1. Allow the engine to run for 90 seconds at 2500 rpm.

  1. Read the heated oxygen sensor voltage while the engine is idling.

    Standard Voltage:
    Heated oxygen sensor voltage alternates between below 0.4 V and higher than 0.5 V (see the following table).


A128474E12


Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 13
A


3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1))
  1. Inspect the heated oxygen sensor (sensor 1) (Click here).



NG
REPLACE HEATED OXYGEN SENSOR (SENSOR 1) (Click here)
OK


4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))
  1. Disconnect the heated oxygen sensor (sensor 1) connector.

  1. Turn the ignition switch to ON.



    A079114E47
  1. Measure the voltage according to the value in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B37-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Heated Oxygen Sensor (Sensor 1))


NG
Go to step 9
OK


5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)
  1. Disconnect the heated oxygen sensor (sensor 1) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B37-1 (HT1A) - B84-109 (HT1A)
    Always
    Below 1 Ω
    B37-3 (OX1A) - B84-112 (OX1A)
    Always
    Below 1 Ω
    B37-4 (E2) - B84-90 (EX1A)
    Always
    Below 1 Ω
    B37-1 (HT1A) or B84-109 (HT1A) - Body ground
    Always
    10 kΩ or higher
    B37-3 (OX1A) or B84-112 (OX1A) - Body ground
    Always
    10 kΩ or higher
    B37-4 (E2) or B84-90 (EX1A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leakage from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


7.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8.CHECK FUEL INJECTOR ASSEMBLY
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) .



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK

REPLACE HEATED OXYGEN SENSOR (SENSOR 1) (Click here)  

9.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - NO. 1 INTEGRATION RELAY)
  1. Disconnect the heated oxygen sensor (sensor 1) connector.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1E-4 - B37-2 (+B)
    Always
    Below 1 Ω
    1E-4 or B37-2 (+B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)  

10.READ VALUE USING INTELLIGENT TESTER (O2S B1S1)
  1. Connect the intelligent tester to the DLC3

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S1

  1. Allow the engine to run at 2500 rpm for 3 minutes.

  1. Depress the accelerator pedal quickly until the engine rpm reaches 4000 rpm 3 times.

    Result 
    Result
    Proceed to
    Higher than 1.0 V
    A
    1.0 V or less
    B



B
Go to step 13
A


11.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
  1. Disconnect the heated oxygen sensor (sensor 1) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B84-109 (HT1A) - B84-112 (OX1A)
    Always
    10 kΩ or higher



NG
Go to step 12
OK

REPLACE ECM (Click here)  

12.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1))
  1. Inspect the heated oxygen sensor (sensor 1) (Click here).



NG
REPLACE HEATED OXYGEN SENSOR (SENSOR 1) (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

13.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


NEXT


14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0130, P0132, P2195 AND/OR P2196)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0130, P0132, P2195 and/or P2196 are output
    A
    DTC is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE HEATED OXYGEN SENSOR (SENSOR 1) (Click here)