Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM

DTC    U0073    Control Module Communication Bus OFF

DTC    U0142    Lost Communication with Main Body ECU

for Preparation Click here


DESCRIPTION

The skid control ECU (brake actuator assembly) receives the signals from the ECM via the CAN communication system.

DTC No.
DTC Detection Condition
Trouble Area
U0073
When any of the following is detected:
  1. When the IG1 terminal voltage is between 10 and 17.4 V, after the output of data from the skid control ECU (brake actuator assembly) is completed, the sending continues for 5 seconds or more.
  2. The condition that bus OFF state occurs once or more within 0.1 seconds occurs 10 times in succession. (Sent signals cannot be received.)
CAN communication system
U0142
No communication with main body ECU
CAN communication system
Main body ECU

INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    EFI Communication Open
    EFI communication open detection / Normal or Error
    Normal: Normal
    Error: Momentary interruption
    -
    Body ECU Communication Open
    Body ECU open detection / Normal or Error
    Normal: Normal
    Error: Momentary interruption
    -

Result 
Result
Proceed to
There is a constant open circuit
A
There are no momentary interruptions
B
There are momentary interruptions
C

HINT:
Perform the above inspection before removing the sensor and connector.



B
Go to step 3

C
Go to step 4
A


2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED
  1. Turn the ignition switch off.

  1. Check if each sensor or ECM connector is securely connected.

    OK:
    Each connector is securely connected.



NG
CONNECT CONNECTOR TO EACH SENSOR OR ECM CORRECTLY
OK


3.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Record the output DTCs (for ABS and CAN communication) (Click here).

    HINT:
    If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for ABS) after the CAN communication system returns to normal.

Result 
Result
Proceed to
DTC (relating to CAN communication system) is output
A
DTC (relating to ABS system) is output
B
DTC is not output
C


B
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)

C
CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)
A

CHECK CAN COMMUNICATION SYSTEM (Click here)  

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Turn the ignition switch off.

  1. Repair or replace the harness or connector.

  1. Check for any momentary interruption between the skid control ECU (brake actuator assembly) and each sensor or ECM (Click here).

  1. Check that there is no momentary interruption.


NEXT


5.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle and turn the steering wheel to the right and left at a speed of 15 km/h (9 mph) or more.

  1. Check that no CAN communication system DTC is output (Click here).

  1. If ABS DTCs are output, record them.

Result 
Result
Proceed to
DTC is not output
A
DTC is output (relating to ABS system)
B
DTC is output (relating to CAN communication system)
C

HINT:
The CAN communication system must be normal when repairing each sensor DTC (for ABS).



B
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)

C
CHECK CAN COMMUNICATION SYSTEM (Click here)
A

END