Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

DTC    C1511    Torque Sensor Circuit Malfunction

DTC    C1512    Torque Sensor Circuit Malfunction

DTC    C1513    Torque Sensor Circuit Malfunction

DTC    C1514    Torque Sensor Power Supply Abnormal

DTC    C1517    Torque Hold Abnormal

for Preparation Click here


DESCRIPTION

The torque sensor converts the rotation torque input from the steering wheel into electric signals and sends them to the power steering ECU assembly.

DTC No.
Detection Item
Trouble Area
C1511
Torque sensor (TRQ1) signal error or stop
  1. Steering column assembly (Torque sensor)
  1. Power steering ECU assembly
C1512
Torque sensor (TRQ2) signal error or stop
C1513
Deviation between torque sensor TRQ1 and TRQ2 exceeds specified value
C1514
Torque sensor power source voltage error
C1517
Temporary control due to malfunction related to torque sensor continues for long time

WIRING DIAGRAM


C239971E01


INSPECTION PROCEDURE

NOTICE:
If the power steering ECU assembly or steering column assembly has been replaced, perform the torque sensor zero point calibration and assist map writing (Click here).

1.CHECK CONNECTOR CONNECTION CONDITION
  1. Check the installation condition of the torque sensor connector.

    OK:
    Torque sensor connector is securely connected to the power steering ECU assembly.



NG
CONNECT CONNECTOR
OK


2.INSPECT POWER STEERING ECU ASSEMBLY (TORQUE SENSOR OUTPUT)
C233844E01
  1. Start the engine.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    z6-8 (TRQV) - z6-2 (TRQG)
    Engine running
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (Power Steering ECU Assembly)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE POWER STEERING ECU ASSEMBLY (Click here)

C
REPLACE POWER STEERING ECU ASSEMBLY (Click here)
A


3.INSPECT POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)
C233844E04
  1. Start the engine.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    z6-9 (TRQ1) - z6-2 (TRQG)
    Engine running, steering wheel not turned (without load)
    2.3 to 2.7 V
    z6-1 (TRQ2) - z6-2 (TRQG)
    Engine running, steering wheel not turned (without load)
    2.3 to 2.7 V
    z6-9 (TRQ1) - z6-2 (TRQG)
    Engine running, steering wheel turned to right with vehicle stopped
    2.5 to 3.8 V
    z6-1 (TRQ2) - z6-2 (TRQG)
    Engine running, steering wheel turned to right with vehicle stopped
    1.2 to 2.5 V
    z6-9 (TRQ1) - z6-2 (TRQG)
    Engine running, steering wheel turned to left with vehicle stopped
    1.2 to 2.5 V
    z6-1 (TRQ2) - z6-2 (TRQG)
    Engine running, steering wheel turned to left with vehicle stopped
    2.5 to 3.8 V

    Text in Illustration 
    *a
    Component with harness connected
    (Power Steering ECU Assembly)

  1. Calculate the difference between the measured TRQV*1 and the sum of the output values of the torque sensor 1 and torque sensor 2.

    HINT:
    *1: TRQV was measured in the previous step.

    OK:
    0.3 V or less

    Result 
    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG (for LHD)
    C
    NG (for RHD)
    D



B
REPLACE POWER STEERING ECU ASSEMBLY (Click here)

C
REPLACE STEERING COLUMN ASSEMBLY (Click here)

D
REPLACE STEERING COLUMN ASSEMBLY (Click here)
A

REPLACE POWER STEERING ECU ASSEMBLY (Click here)