Home › Suspension › REAR SUSPENSION › REAR COIL SPRING

REAR COIL SPRING > INSTALLATION

for Preparation Click here



1. INSTALL REAR COIL SPRING LH
  1. Install the rear coil spring lower insulator LH onto the rear axle beam assembly.



    C110329E04
  1. Install the rear coil spring upper insulator LH so that its gap fits onto the end of rear coil spring LH.
    Text in Illustration 
    *a
    Fit



    C233115
  1. Install the rear coil spring LH onto the rear axle beam assembly.
    Text in Illustration 
    V100144
    Paint Mark

    NOTICE:
    The paint mark of the rear coil spring LH should be towards the underside and rear side of the vehicle.



2. INSTALL REAR COIL SPRING RH

HINT:
Use the same procedure for the RH side as for the LH side.



3. TEMPORARILY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH
  1. Support the rear axle beam assembly with a jack. Insert a wooden block between the jack and the rear axle spring seat to prevent damage.

  1. Jack up the rear axle beam assembly slowly, and provisionally install the rear shock absorber assembly LH (lower side) with the bolt and nut onto the rear axle beam assembly.



4. TEMPORARILY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



5. INSTALL REAR FLEXIBLE HOSE LH
  1. Connect the rear flexible hose LH onto the rear axle beam assembly with a new clip.

  1. Using a union nut wrench (10 mm), install the brake tube to the rear flexible hose LH while holding the rear flexible hose LH with a wrench.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



6. INSTALL REAR FLEXIBLE HOSE RH

HINT:
Use the same procedure for the RH side as for the LH side.



7. INSTALL SKID CONTROL SENSOR WIRE LH (w/ ABS)
  1. Install the skid control sensor wire LH onto the rear axle beam assembly with the nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Connect the skid control sensor wire LH connector.



8. INSTALL SKID CONTROL SENSOR WIRE RH (w/ ABS)

HINT:
Use the same procedure for the RH side as for the LH side.



9. STABILIZE SUSPENSION
  1. Lower the vehicle from the jack.

  1. Bounce the vehicle up and down several times to stabilize the suspension.



10. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



11. FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY


    C204012E02
  1. Suspend the jack on the rear axle spring seat and adjust the length of the rear shock absorber assembly to the reference value.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side

    Length of shock absorber:
    220 mm (8.66 in.)

  1. Fully tighten the 2 bolts.

    Torque:
    90 N*m{ 918 kgf*cm , 66 ft.*lbf }



12. FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH
  1. Fully tighten the rear shock absorber assembly (lower side) with the bolt.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



13. FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



14. BLEED BRAKE LINE
(Click here)


15. BLEED CLUTCH LINE (for Manual Transaxle)
(Click here)


16. INSPECT REAR WHEEL ALIGNMENT
(Click here)


17. CHECK SPEED SENSOR SIGNAL (w/ ABS)
(Click here)


18. CHECK SPEED SENSOR SIGNAL (w/ VSC)
(Click here)