Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK COMBINATION METER ASSEMBLY

E219768E01

  1. Disconnect the F1 combination meter assembly connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Terminals No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F1-21 (ET) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F1-39 (IG+) - Body ground
    P - Body ground
    Ignition switch signal
    Ignition switch off → ON
    Below 1 V → 11 to 14 V
    F1-40 (B) - Body ground
    L - Body ground
    Battery
    Always
    11 to 14 V
    F3-1 (B) - Body ground
    R - Body ground
    Battery
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the F1 combination meter assembly connector.



  4. Measure the resistance, voltage and check for pulse of the wire harness side connector.

    Terminals No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F1-5 (SI) - Body ground
    L - Body ground
    Speed signal (Input)
    Driving at approximately
    20 km/h (12 mph)
    Pulse generation
    (See waveform 1)
    F1-6 (+S) - Body ground
    SB - Body ground
    Speed signal (Output)
    Driving at approximately
    20 km/h (12 mph)
    Pulse generation
    (See waveform 1)
    F1-7 (P/SB) - Body ground
    P - Body ground
    Front seat inner belt assembly signal (passenger side)
    Front passenger seat is occupied and its seat belt is unfastened → fastened
    Below 1 V → 11 to 14 V
    F1-9 (S) - Body ground
    Y - Body ground
    Engine oil pressure signal
    Engine oil pressure warning light ON → OFF
    Below 1 V → 11 to 14 V
    F1-11 (CHK) - Body ground
    LG - Body ground
    Check engine warning light signal
    Check engine warning light ON → OFF
    Below 1 V → 11 to 14 V
    F1-12 (SW) - Body ground
    GR - Body ground
    Brake fluid level warning light signal
    Ignition switch ON
    Brake fluid level warning light ON → OFF
    Below 1 V → 11 to 14 V
    F1-14 (-) - Body ground
    BR - Body ground
    High beam indicator signal (-)
    Always
    Below 1 V
    F1-16 (L) - Body ground
    G - Body ground
    Fuel level signal
    Ignition switch ON
    Fuel level is FULL → EMPTY
    Below 1 V → 4.5 to 9.0 V
    F1-19 (+) - Body ground
    GR - Body ground
    High beam indicator signal (+)
    High beam indicator ON → OFF
    11 to 14 V → Below 1 V
    F1-20 (ILL+) - Body ground
    R - Body ground
    Taillight signal
    Light control switch OFF → ON
    Below 1 V → 11 to 14 V
    F1-31 (CANL) - Body ground
    W - Body ground
    CAN communication line
    Ignition switch ON
    Pulse generation
    F1-32 (CANH) - Body ground
    G - Body ground
    CAN communication line
    Ignition switch ON
    Pulse generation
    F3-3 (HAZ) - Body ground
    L - Body ground
    Hazard warning signal switch signal
    Hazard warning signal switch off
    11 to 14 V
    Hazard warning signal switch on
    Below 1 Ω
    F3-7 (LR) - Body ground
    V - Body ground
    Right turn signal
    Ignition switch ON
    Right turn indicator light OFF → ON
    Below 1 V → 11 to 14 V
    F3-9 (ER) - Body ground
    B - Body ground
    Turn signal switch RH signal
    Turn signal switch RH on
    11 to 14 V
    Turn signal switch RH off
    Below 1 Ω
    F3-10 (EL) - Body ground
    Y - Body ground
    Turn signal switch LH signal
    Turn signal switch LH on
    11 to 14 V
    Turn signal switch LH off
    Below 1 Ω
    F3-12 (FOG)*1 - Body ground
    BE - Body ground
    Front fog signal
    Ignition switch ON
    Front fog switch OFF → ON
    Below 1 V → 11 to 14 V
    F3-13 (LL) - Body ground
    LG - Body ground
    Left turn signal
    Ignition switch ON
    Left turn indicator light OFF → ON
    Below 1 V → 11 to 14 V

    1. *1: w/ Fog Light
    If the result is not as specified, the combination meter assembly may have a malfunction.



      E115032E01
    1. Waveform 1: Using an oscilloscope
      Item
      Condition
      Terminal Connections
      F1-6 (+S) and Body ground
      F1-5 (SI) and Body ground
      Tool Setting
      5 V/DIV, 20 ms/DIV
      Condition
      Driving at approximately 20 km/h (12 mph)

      HINT:
      As the vehicle speed increases, the cycle of the signal waveform narrows.


CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

E219866E03


Text in Illustration 
*A
for LHD
*B
for RHD
*1
Instrument Panel Junction Block Assembly
*2
Main Body ECU
(Multiplex Network Body ECU)
  1. Remove the main body ECU (multiplex network body ECU) (Click here).

  2. Measure the resistance and voltage between each terminal of the wire harness side connectors and body ground.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-11 (GND1) - Body ground
    None - Body ground
    Ground
    Always
    Below 1 Ω
    MB-29 (ACC) - Body ground
    None - Body ground
    Ignition power supply (ACC signal)
    Ignition switch ACC
    11 to 14 V
    MB-30 (BECU) - Body ground
    None - Body ground
    +B (power system signal system) power supply
    Always
    11 to 14 V
    MB-31 (ALTB) - Body ground
    None - Body ground
    +B (power system alternator system) power supply
    Always
    11 to 14 V
    MB-32 (IG) - Body ground
    None - Body ground
    Ignition power supply (IG signal)
    Ignition switch ON
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Install the main body ECU (multiplex network body ECU) (Click here).

  4. Measure the voltage and check for pulse between each terminal of the wire harness side connectors and body ground.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3A-28 (PKB) - Body ground
    R - Body ground
    Parking brake signal
    Parking brake warning light ON → OFF
    Below 1 V → 11 to 14 V
    3D-34 (DBKL) - Body ground
    W - Body ground
    Front seat inner belt assembly signal (driver side)
    Driver seat belt warning light OFF → ON
    Below 1 V → 11 to 14 V
    F76-13 (CANL) - Body ground
    W - Body ground
    CAN communication line
    Ignition switch ON
    Pulse generation
    F76-14 (CANH) - Body ground
    R - Body ground
    CAN communication line
    Ignition switch ON
    Pulse generation
    If the result is not as specified, there may be a malfunction in the wire harness.


COMBINATION METER INTERNAL CIRCUIT

E231150E01


E231151E01


E231152E01


E231153E01


Connectors 
Terminal No.
Wire Harness Side
F1
5
Brake actuator assembly (Skid control ECU)*1 or Speedometer sensor*2
6
Other ECU
7
Occupant detection sensor and Front seat inner belt assembly (Front passenger side)
9
Engine oil pressure switch assembly
11
ECM
12
Brake fluid level warning switch
14
Body ground
16
Fuel sender gauge assembly
19
H-LP LH HI fuse
20
Panel fuse
21
Body ground
31
CAN communication line
32
CAN communication line
39
IG2 relay
40
Battery
F3
1
Battery
3
Hazard warning signal switch assembly
7
Turn signal light RH
9
Headlight dimmer switch assembly (Turn signal switch)
10
Headlight dimmer switch assembly (Turn signal switch)
12
FR FOG relay*3
13
Turn signal light LH
  1. *1: w/ ABS
  2. *2: w/o ABS
  3. *3: w/ Fog Light