Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR (for 3 Door)

REAR AIRBAG SENSOR (for 3 Door) > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



3. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
(Click here)


4. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
(Click here)


5. REMOVE REAR SEAT ASSEMBLY (for Fold Down Seat Type)
(Click here)


6. REMOVE DECK BOARD ASSEMBLY


    B272608
  1. Remove the deck board.



7. REMOVE SPARE WHEEL COVER


    B272609
  1. Remove the spare wheel cover.



8. REMOVE NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)


    E222045E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw.
    Text in Illustration 
    *1
    Protective Tape

  1. Disconnect the connector and remove the No. 2 room light assembly.



9. REMOVE JACK HANDLE (for RH Side)


10. REMOVE REAR FLOOR FINISH PLATE


    B272624
  1. Disengage the 4 claws and 4 guides and remove the rear floor finish plate.



11. REMOVE FRONT DOOR SCUFF PLATE


    B284313
  1. Disengage the 8 claws and remove the front door scuff plate.



12. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP


    B284315
  1. Remove the front door opening trim weatherstrip.



13. REMOVE FRONT SEAT BELT OUTER BAR SUB-ASSEMBLY


    B282674
  1. Remove the 2 bolts and front seat belt outer bar sub-assembly, disconnect the floor anchor part of the front seat outer belt assembly.



14. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY


    B284318
  1. Disengage the 8 clips and 10 claws.

  1. Disengage the 3 guides and remove the quarter trim panel.



15. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY


    B284323
  1. Remove the bolt.

  1. Disengage the 2 claws and separate the rear seat 3 point type outer belt.



16. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)


    B284324
  1. Remove the 3 screws.

  1. Disengage the 3 clips and the 3 claws and remove the deck trim side panel.



17. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)

HINT:
Use the same procedure as for the RH side.



18. REMOVE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B282661
  1. Disconnect the connector from the No. 2 side airbag sensor assembly.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.




    1. Push and hold the white housing lock, and slide the outer connector locking sleeve.


      C195226E09


      Text in Illustration 
      *1
      Housing Lock
      *2
      Outer Connector Locking Sleeve
      *a
      Slide
      -
      -

    2. Push and hold the white housing lock again, and slide the yellow outer connector locking sleeve to disconnect the connector.



    B282662
  1. Remove the bolt and No. 2 side airbag sensor assembly.

    NOTICE:
    Loosen the bolt while holding the No. 2 side airbag sensor assembly because the No. 2 side airbag sensor assembly pin (stopper) is easily damaged.