Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR (for 3 Door)

REAR AIRBAG SENSOR (for 3 Door) > INSTALLATION

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

HINT:
The procedure described below is for the RH side. Use the same procedure for both the LH and RH sides, unless otherwise specified.



1. INSTALL NO. 2 SIDE AIRBAG SENSOR ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Insert the pin (stopper) into the body hole to install the No. 2 side airbag sensor assembly to the vehicle with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the No. 2 side airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the No. 2 side airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
    3. Make sure that the pin (stopper) is securely inserted into the body hole.
    4. Tighten the bolt while holding the No. 2 side airbag sensor assembly because the No. 2 side airbag sensor assembly pin (stopper) is easily damaged.



  1. Connect the connector to the No. 2 side airbag sensor assembly.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.




    1. Connect the connector as shown in the illustration (when locking, make sure that the outer connector locking sleeve returns to its original position and a click sound can be heard).


      C198070E06


      Text in Illustration 
      *1
      Outer Connector Locking Sleeve
      -
      -
      *a
      Slide
      -
      -

      HINT:
      When connected, the outer connector locking sleeve will slide. Be sure not to hold the outer connector locking sleeve while connecting, as it may result in an insecure fit.

  1. Check that there is no looseness in the installation parts of the No. 2 side airbag sensor assembly.



2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)
  1. Engage the 3 clips and the 3 claws and install the deck trim side panel.

  1. Install the 3 screws.



3. INSTALL ROOF SIDE INNER GARNISH LH (for LH Side)
  1. Pass the rear seat 3 point type outer belt through the slit in the roof side inner garnish.

  1. Engage the 5 clips and install the roof side inner garnish.



4. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY
  1. Engage the 2 claws and install the rear seat 3 point type outer belt.

  1. Tighten the bolt.

    Torque:
    41 N*m{ 420 kgf*cm , 30 ft.*lbf }



5. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY
  1. Engage the 8 clips and the 10 claws.

  1. Engage the 3 guides and install the quarter trim panel.



6. INSTALL FRONT SEAT BELT OUTER BAR SUB-ASSEMBLY
  1. Connect the floor anchor part of the front seat outer belt assembly and install the front seat belt outer bar sub-assembly with the 2 bolts.

    Torque:
    41 N*m{ 420 kgf*cm , 30 ft.*lbf }



7. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP


    B284341E01
  1. Align the paint mark on the front door opening trim weatherstrip with the flange position on the vehicle body and install the weatherstrip.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Flange Position

    Paint Mark:
    Area
    Color
    RH Side
    Yellow
    LH Side
    White

    NOTICE:
    After installation, check that the corners fit correctly.



8. INSTALL FRONT DOOR SCUFF PLATE
  1. Engage the 8 claws and install the front door scuff plate.



9. INSTALL REAR FLOOR FINISH PLATE
  1. Engage the 4 guides and the 4 claws to install the rear floor finish plate.



10. INSTALL JACK HANDLE (for RH Side)


11. INSTALL NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)
  1. Connect the connector.



    E222046
  1. Engage the claw to install the No. 2 room light assembly.



12. INSTALL SPARE WHEEL COVER
  1. Install the spare wheel cover.



13. INSTALL DECK BOARD ASSEMBLY
  1. Install the deck board.



14. INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)
(Click here)


15. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
(Click here)


16. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
(Click here)


17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



18. INSPECT SRS WARNING LIGHT
(Click here)