Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

DTC    B2312    Driver Side Door Master Switch Malfunction

for Preparation Click here


DESCRIPTION

The power window regulator motor consists of the motor, regulator and ECU. The power window regulator motor is driven by operating the power window switch. This DTC is output when the ECU built into the regulator motor determines that the power window switch is stuck.

DTC No.
DTC Detection Condition
Trouble Area
B2312
  1. The power window regulator master switch assembly is stuck.
  2. The power window regulator master switch assembly is held in the same position for more than 20 seconds.
  1. Power window regulator master switch assembly
  2. Power window regulator motor assembly LH or RH (driver side)
  3. Harness or connector

WIRING DIAGRAM


B291663E01


B291663E02


INSPECTION PROCEDURE

NOTICE:
  1. The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the power window control system after confirming that the communication system is functioning properly.
  2. When the power window regulator motor assembly LH or RH (driver side) is reinstalled or replaced, the power window control system must be initialized.
  3. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be resumed by repeating the following operations at least 5 times:
    1. Close the power window by fully pulling up the power window regulator master switch assembly and holding it in the auto up position.
    2. Open the power window by fully pushing down the power window regulator master switch assembly.

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / D-Door Motor / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    D-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Auto SW
    Driver side power window auto switch signal /
    OFF or ON
    OFF: Driver side door power window auto switch not operated
    ON: Driver side door power window auto switch operated
    -
    D Door P/W Up SW
    Driver side power window manual up switch signal /
    OFF or ON
    OFF: Driver side door power window manual up switch not operated
    ON: Driver side door power window manual up switch operated
    -
    D Door P/W Down SW
    Driver side power window manual down switch signal /
    OFF or ON
    OFF: Driver side door power window manual down switch not operated
    ON: Driver side door power window manual down switch operated
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 2
OK

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE) 

2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
  1. Inspect the power window regulator master switch assembly (Click here).



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - POWER WINDOW REGULATOR MOTOR LH OR RH AND BODY GROUND)
  1. for LHD

    1. Disconnect the H1 power window regulator master switch assembly connector.

    2. Disconnect the H3 power window regulator motor assembly LH (driver side) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      w/ Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      H1-8 (UP) - H3-10 (UP)
      Always
      Below 1 Ω
      H1-5 (DOWN) - H3-7 (DOWN)
      Always
      Below 1 Ω
      H1-4 (AUTO) - H3-4 (AUTO)
      Always
      Below 1 Ω
      H1-1 (GND) - Body ground
      Always
      Below 1 Ω
      H1-8 (UP) - Body ground
      Always
      10 kΩ or higher
      H1-5 (DOWN) - Body ground
      Always
      10 kΩ or higher
      H1-4 (AUTO) - Body ground
      Always
      10 kΩ or higher
      w/o Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      H1-18 (UP) - H3-10 (UP)
      Always
      Below 1 Ω
      H1-10 (DOWN) - H3-7 (DOWN)
      Always
      Below 1 Ω
      H1-1 (AUTO) - H3-4 (AUTO)
      Always
      Below 1 Ω
      H1-7 (GND) - Body ground
      Always
      Below 1 Ω
      H1-18 (UP) - Body ground
      Always
      10 kΩ or higher
      H1-10 (DOWN) - Body ground
      Always
      10 kΩ or higher
      H1-1 (AUTO) - Body ground
      Always
      10 kΩ or higher

  1. for RHD

    1. Disconnect the G1 power window regulator master switch assembly connector.

    2. Disconnect the G3 power window regulator motor assembly RH (driver side) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      w/ Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      G1-1 (UP) - G3-10 (UP)
      Always
      Below 1 Ω
      G1-5 (DOWN) - G3-7 (DOWN)
      Always
      Below 1 Ω
      G1-4 (AUTO) - G3-4 (AUTO)
      Always
      Below 1 Ω
      G1-9 (GND) - Body ground
      Always
      Below 1 Ω
      G1-1 (UP) - Body ground
      Always
      10 kΩ or higher
      G1-5 (DOWN) - Body ground
      Always
      10 kΩ or higher
      G1-4 (AUTO) - Body ground
      Always
      10 kΩ or higher
      w/o Rear Power Window 
      Tester Connection
      Condition
      Specified Condition
      G1-9 (UP) - G3-10 (UP)
      Always
      Below 1 Ω
      G1-6 (DOWN) - G3-7 (DOWN)
      Always
      Below 1 Ω
      G1-18 (AUTO) - G3-4 (AUTO)
      Always
      Below 1 Ω
      G1-7 (GND) - Body ground
      Always
      Below 1 Ω
      G1-9 (UP) - Body ground
      Always
      10 kΩ or higher
      G1-6 (DOWN) - Body ground
      Always
      10 kΩ or higher
      G1-18 (AUTO) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH (DRIVER SIDE) (Click here)