Home › Audio/Visual/Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Radio Broadcast cannot be Received or Poor Reception

for Preparation Click here


INSPECTION PROCEDURE

1.CHECK RADIO RECEIVER ASSEMBLY
  1. Check the radio automatic station search function.

    1. Check the radio automatic station search function by activating it.

      OK:
      The radio automatic station search function works properly.



NG
Go to step 2
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)  

2.CHECK OPTIONAL COMPONENTS
  1. Check if any optional components, such as a telephone antenna, are installed.
    Result 
    Result
    Proceed to
    Optional components are installed
    A
    Optional components are not installed
    B

    NOTICE:
    Do not remove optional components without the permission of the customer.



B
Go to step 3
A

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE) 

3.CHECK ANTENNA FOR NOISE PRODUCTION
  1. With the ignition switch ACC, turn on the radio and select the AM mode.

  1. Remove the roof antenna pole sub-assembly.

  1. Place the tip of a screwdriver on the antenna and check that noise is heard from the speaker.

    OK:
    Noise occurs.

  1. Install the roof antenna pole sub-assembly.



NG
Go to step 4
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)  

4.CHECK INSTALLATION OF ANTENNA GROUND
  1. Check that the amplifier antenna ground is securely fastened to the body.

    OK:
    Ground is securely fastened to body.

  1. Check that the antenna cord sub-assembly ground is securely fastened to the body.

    OK:
    Ground is securely fastened to body.



NG
CORRECTLY INSTALL GROUND
OK


5.CHECK AMPLIFIER ANTENNA ASSEMBLY


    E229625E01
  1. Disconnect the amplifier antenna connectors.

  1. With the ignition switch ON, turn on the radio and select the AM mode.

  1. Place the tip of a screwdriver against the metal terminal of the No. 2 antenna cord sub-assembly and check that noise is heard from speakers.

    OK:
    Noise occurs.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3 - Body ground
    During radio (AM) reception
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Amplifier Antenna Assembly)

  1. Reconnect the amplifier antenna connectors.



NG
Go to step 6
OK

REPLACE AMPLIFIER ANTENNA ASSEMBLY (Click here)  

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY


    E170033E02
  1. Disconnect the No. 2 antenna cord sub-assembly connectors.

  1. With the ignition switch ACC, turn on the radio and select the AM mode.

  1. Place the tip of a screwdriver against the metal terminal of the No. 2 antenna cord sub-assembly and check that noise is heard from speakers.

    OK:
    Noise occurs.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3 - Body ground
    During radio (AM) reception
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 2 Antenna Cord Sub-Assembly)

  1. Reconnect the No. 2 antenna cord sub-assembly connectors.



NG
Go to step 7
OK

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY (Click here)  

7.CHECK RADIO RECEIVER ASSEMBLY


    E159266
  1. Disconnect the antenna connector from the radio receiver assembly.

  1. With the radio receiver assembly connector connected, turn the ignition switch to ACC.

  1. Turn on the radio and select the AM mode.

  1. Place the tip of a screwdriver against the metal terminal of the radio receiver assembly and check that noise is heard from the speaker.

    OK:
    Noise occurs.



    E221708E01
  1. Reconnect the antenna connector to the radio receiver assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    5 - Body ground
    During radio (AM) reception
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Radio Receiver Assembly)



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK

REPLACE ANTENNA CORD SUB-ASSEMBLY (Click here)