Home › Engine / Hybrid System · 2NZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0133    Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P0031 .

HINT:
Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DTC No.
DTC Detection Condition
Trouble Area
P0133
While idling with warm engine, response time for voltage output of heated oxygen sensor to change from rich to lean or from lean to rich is 1 second or more (2 trip detection logic)
  1. Open or short in heated oxygen sensor (sensor 1) circuit
  2. Heated oxygen sensor (sensor 1)
  3. Heated oxygen sensor heater (sensor 1)
  4. No. 1 integration relay (EFI MAIN relay)
  5. Intake system
  6. Fuel pressure
  7. Fuel injector assembly
  8. ECM

MONITOR DESCRIPTION

The ECM uses the heated oxygen sensor information to regulate the air-fuel ratio close to the stoichiometric air-fuel ratio. This maximizes the catalytic converter's ability to purify the exhaust gases. The sensor detects oxygen levels in the exhaust gas and sends a signal to the ECM.
The inner surface of the sensor element is exposed to outside air. The outer surface of the sensor element is exposed to the exhaust gases. The sensor element is made of platinum coated zirconia and includes an integrated heating element. The heated oxygen sensor's output voltage changes suddenly in the vicinity of the stoichiometric air-fuel ratio. The heated oxygen sensor generates waveforms of a voltage between 0 V and 1 V in response to the oxygen concentration in the exhaust gas. When the heated oxygen sensor voltage is 0.45 V or more, the ECM judges that the air-fuel ratio is rich. When it is 0.45 V or less, the ECM judges that the air-fuel ratio is lean. The ECM monitors the response feature of the heated oxygen sensor. If the response time of the heated oxygen sensor status change from rich to lean (or vice versa) becomes longer, the ECM interprets this as a malfunction in the heated oxygen sensor and stores a DTC.

A084946E16


A106048E07


MONITOR STRATEGY


Required Sensors/Components (Main)
Heated oxygen sensor (sensor 1)
Required Sensors/Components (Related)
Mass air flow meter, Throttle with motor body assembly, Crankshaft position sensor, Vehicle speed sensor
Frequency of Operation
Once per driving cycle

TYPICAL ENABLING CONDITIONS


Duration that vehicle has run with the following conditions A and B
15 seconds or more
A. Vehicle speed
40 km/h (25 mph) or more
B. Engine speed
900 rpm or more
Time after engine start
120 seconds or more
Idle
ON
Fuel system status
Closed loop
Vehicle speed
Less than 5 km/h (3 mph)
Engine coolant temperature
75°C (167°F) or more

TYPICAL MALFUNCTION THRESHOLDS


One of the following conditions is met
-
Average of switch time from lean to rich*
1 second or more
Average of switch time from rich to lean*
1 second or more
* Lean
0.4 V or lower
* Rich
0.5 V or higher

CONFIRMATION DRIVING PATTERN


A257482E01

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on.
  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
  7. Allow the engine to idle for 120 seconds or more [B].
  8. Drive the vehicle at 40 km/h (25 mph) or more for 35 seconds [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Idle the engine for 40 seconds or more [D].
  10. Perform step [C] and [D] at least 3 times.
  11. Enter the following menus: Powertrain / Engine and ECT / DTC [E].
  12. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  13. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  14. Input the DTC: P0133.
  15. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E].


WIRING DIAGRAM

Refer to DTC P0031 .

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume function provided in the Active Test. The Control the Injection Volume function can help to determine whether the heated oxygen sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester on.
  3. Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
  5. Perform the Active Test operation with the engine idling.
  6. Monitor the output voltages of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the tester.

HINT:
  1. Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Tester Display
(Sensor)
Injection Volume
Status
Voltage
O2S B1S1
(Heated oxygen sensor (sensor 1))
+12%
Rich
Higher than 0.5 V
-12%
Lean
Below 0.4 V
O2S B1S2
(Heated oxygen sensor (sensor 2))
+12%
Rich
Higher than 0.5 V
-12%
Lean
Below 0.4 V

NOTICE:
The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.


Case
Heated Oxygen Sensor (Sensor 1) Output Voltage
Heated Oxygen Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E05
A150789E07
A150787E05
A150788E09
-
2
A150787E05
A150790E01
A150787E05
A150788E09
  1. Heated oxygen sensor (Sensor 1)
  2. Heated oxygen sensor heater (Sensor 1)
  3. Heated oxygen sensor circuit (Sensor 1)
3
A150787E05
A150789E07
A150787E05
A150790E01
  1. Heated oxygen sensor (Sensor 2)
  2. Heated oxygen sensor heater (Sensor 2)
  3. Heated oxygen sensor circuit (Sensor 2)
4
A150787E05
A150790E01
A150787E05
A150790E01
  1. Fuel injector assembly
  2. Fuel pressure
  3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)

HINT:
  1. Following the Control the Injection Volume procedure enables technicians to check and graph the voltage outputs of both heated oxygen sensors
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / O2S B1S1 and O2S B1S2, then press the view button.

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0133)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P0133 is output
    A
    DTC P0133 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0133 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (O2S B1S1)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S1.

  1. Warm up the heated oxygen sensor at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Read the voltage output of the front heated oxygen sensor displayed on the tester, while the engine is idling.

    Standard:
    Fluctuates between below 0.4 V and higher than 0.5 V, and period "t" is less than 1 second (refer to table below).


A128469E06


Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 10
A


3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1))
  1. Inspect the heated oxygen sensor (sensor 1) (Click here).



NG
REPLACE HEATED OXYGEN SENSOR (SENSOR 1) (Click here)
OK


4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))
  1. Disconnect the heated oxygen sensor (sensor 1) connector.

  1. Turn the ignition switch to ON.



    A079114E48
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B37-2 (+B) -Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Heated Oxygen Sensor (Sensor 1))



NG
Go to step 9
OK


5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)
  1. Disconnect the heated oxygen sensor (sensor 1) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B37-1 (HT1A) - B84-109 (HT1A)
    Always
    Below 1 Ω
    B37-3 (OX1A) - B84-112 (OX1A)
    Always
    Below 1 Ω
    B37-4 (E2) - B84-90 (EX1A)
    Always
    Below 1 Ω
    B37-1 (HT1A) or B84-109 (HT1A) - Body ground
    Always
    10 kΩ or higher
    B37-3 (OX1A) or B84-112 (OX1A) - Body ground
    Always
    10 kΩ or higher
    B37-4 (E2) or B84-90 (EX1A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leakage from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


7.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8.INSPECT FUEL INJECTOR ASSEMBLY
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK

REPLACE HEATED OXYGEN SENSOR (SENSOR 1) (Click here)  

9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - HEATED OXYGEN SENSOR (SENSOR 1))
  1. Disconnect the heated oxygen sensor (sensor 1) connector.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B37-2 (+B) - 1E-4
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO.1 INTEGRATION RELAY (Click here)  

10.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


NEXT


11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0133)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0133 is output
    A
    DTC is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE HEATED OXYGEN SENSOR (SENSOR 1) (Click here)