Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM (except Separate Type Yaw Rate Sensor)

CAN COMMUNICATION SYSTEM (except Separate Type Yaw Rate Sensor) > Open in CAN Main Bus Line (LHD Models)

for Preparation Click here


DESCRIPTION

There may be an open circuit in the CAN main wire and/or DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or higher.

Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or higher.
  1. CAN main wire or connector
  2. No. 1 junction connector
  3. No. 2 junction connector
  4. ECM
  5. Combination meter assembly
  6. DLC3 branch wire or connector

WIRING DIAGRAM


E231140E01


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.CHECK DLC3


    C152423E05
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F4-6 (CANH) - F4-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of DLC3

    HINT:
    When the measured value is 133 Ω or higher and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "How to Proceed with Troubleshooting" (Click here) after repairing the trouble area.



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (DLC3 BRANCH WIRE)
OK


2.CHECK CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR)


    E219745E18
  1. Disconnect the F83 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F83-10 (CANH) - F83-21 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 7
OK


3.CONNECT CONNECTOR
  1. Reconnect the F83 No. 2 junction connector.


NEXT


4.CHECK CAN MAIN WIRE OR CONNECTOR (COMBINATION METER ASSEMBLY)
E186731E15
  1. Disconnect the F1 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F1-32 (CANH) - F1-31 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
Go to step 5
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

5.CONNECT CONNECTOR
  1. Reconnect the F1 combination meter assembly connector.


NEXT


6.CHECK CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
E219745E20
  1. Disconnect the F83 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F83-7 (CANH) - F83-18 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
OK

REPLACE NO. 2 JUNCTION CONNECTOR 

7.CONNECT CONNECTOR
  1. Reconnect the F83 No. 2 junction connector.


NEXT


8.CHECK CAN MAIN WIRE OR CONNECTOR (ECM)
  1. Disconnect the A74 ECM connector.



    E191962E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A74-41 (CANH) - A74-49 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)
    Result 
    Result
    Proceed to
    NG
    A
    OK (1NZ-FE)
    B
    OK (2NZ-FE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A


9.CONNECT CONNECTOR
  1. Reconnect the A74 ECM connector.


NEXT


10.CHECK CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - ECM)
E219745E21
  1. Disconnect the A61 and F82 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A61-9 (CANH) - A61-20 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ECM - NO. 1 JUNCTION CONNECTOR)
OK


11.CHECK CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
E219745E22
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F82-4 (CANH) - F82-15 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 1 JUNCTION CONNECTOR