CAN COMMUNICATION SYSTEM (for Separate Type Yaw Rate Sensor) > Open in CAN Main Bus Line |
| Symptom | Trouble Area |
| The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or higher. |
|

| 1.CHECK DLC3 |
![]() |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F4-6 (CANH) - F4-14 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Front view of DLC3 |
|
| ||||
| OK | |
| 2.CHECK CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR) |
![]() |
Disconnect the F83 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F83-10 (CANH) - F83-21 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
|
| ||||
| OK | |
| 3.CONNECT CONNECTOR |
Reconnect the F83 No. 2 junction connector.
| NEXT | |
| 4.CHECK CAN MAIN WIRE OR CONNECTOR (COMBINATION METER ASSEMBLY) |
![]() |
Disconnect the F1 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F1-32 (CANH) - F1-31 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
|
| ||||
| OK | ||
| ||
| 5.CONNECT CONNECTOR |
Reconnect the F1 combination meter assembly connector.
| NEXT | |
| 6.CHECK CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) |
![]() |
Disconnect the F83 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F83-7 (CANH) - F83-18 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
|
| ||||
| OK | ||
| ||
| 7.CONNECT CONNECTOR |
Reconnect the F83 No. 2 junction connector.
| NEXT | |
| 8.CHECK CAN MAIN WIRE OR CONNECTOR (ECM) |
Disconnect the A74 ECM connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A74-41 (CANH) - A74-49 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Front view of wire harness connector (to ECM) |
| Result | Proceed to |
| NG | A |
| OK (1NZ-FE) | B |
| OK (2NZ-FE) | C |
|
| ||||
|
| ||||
| A | |
| 9.CONNECT CONNECTOR |
Reconnect the A74 ECM connector.
| NEXT | |
| 10.CHECK CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - ECM) |
![]() |
Disconnect the A61 and F82 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A61-9 (CANH) - A61-20 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
|
| ||||
| OK | |
| 11.CHECK CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F82-4 (CANH) - F82-15 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
|
| ||||
| OK | ||
| ||