Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM (except Separate Type Yaw Rate Sensor)

CAN COMMUNICATION SYSTEM (except Separate Type Yaw Rate Sensor) > Open in One Side of CAN Branch Line

for Preparation Click here


DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen, one side of the CAN branch wire may be open (one side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open).

Symptom
Trouble Area
2 or more ECUs and/or sensors do not appear on the intelligent tester "CAN Bus Check" screen.
  1. Open in side of CAN branch wire
  2. Airbag sensor assembly
  3. Skid control ECU (brake actuator assembly)
  4. Main body ECU (multiplex network body ECU)
  5. Power steering ECU assembly
  6. Steering angle sensor (spiral cable sub-assembly)*1
  7. Air conditioning amplifier assembly*2
  8. No. 1 junction connector
  9. No. 2 junction connector
  1. *1: w/ VSC
  2. *2: w/ Cooler

WIRING DIAGRAM


E231142E02


E231143E02


E231144E02


E231145E02


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
  2. Perform the following inspection for the ECUs (sensors) which are not displayed on the intelligent tester. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.
  3. Do not remove the combination meter assembly and ECM, as they are the end parts of the circuit. If removed, CAN communication will not be possible.
  4. The open circuit confirmation of the combination meter assembly, ECM and main wire is performed in the "Check CAN Bus Line" procedure of "How to Proceed with Troubleshooting". This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.

1.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
  1. Disconnect the A54*1 or A55*2 skid control ECU (brake actuator assembly) connector.
    *1: w/ VSC
    *2: w/o VSC

  1. Select "Communication Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    "Skid Control (ABS/VSC/TRAC)" not displayed on intelligent tester.
    A
    Several ECUs and sensors other than "Skid Control (ABS/VSC/TRAC)" not displayed on intelligent tester.
    B



B
Go to step 3
A


2.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE)
E186734E26
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A54-25 (CANH) - A54-14 (CANL)*1
    A55-25 (CANH) - A55-14 (CANL)*2
    Ignition switch off
    54 to 69 Ω

    *1: w/ VSC
    *2: w/o VSC
    Text in Illustration 
    *A
    w/ VSC
    *B
    w/o VSC
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))
    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD with VSC)
    C
    OK (for RHD without VSC)
    D

  1. Reconnect the A54*1 or A55*2 skid control ECU (brake actuator assembly) connector.

*1: w/ VSC
*2: w/o VSC


B
REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) (Click here)

C
REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

D
REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
A

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE) 

3.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)

HINT:
For vehicles without cooler, go to step 5.

  1. Disconnect the F42*1 or F41*2 air conditioning amplifier assembly connector.

*1 : for Automatic Air Conditioning System
*2 : for Manual Air Conditioning System (w/ Cooler)
  1. Select "Communication Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    "Air Conditioning Amplifier" not displayed on intelligent tester.
    A
    Several ECUs and sensors other than "Air Conditioning Amplifier" not displayed on intelligent tester.
    B



B
Go to step 5
A


4.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
E217717E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F42-11 (TX+) - F42-12 (TX-)*1
    F41-8 (TX+) - F41-9 (TX-)*2
    Ignition switch off
    54 to 69 Ω

    *1 : for Automatic Air Conditioning System
    *2 : for Manual Air Conditioning System (w/ Cooler)
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System))
    *b
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly (for Manual Air Conditioning System (w/ Cooler)))

  1. Reconnect the F42*1 or F41*2 air conditioning amplifier assembly connector.

*1 : for Automatic Air Conditioning System
*2 : for Manual Air Conditioning System (w/ Cooler)


NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

5.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIRBAG SENSOR ASSEMBLY)
  1. Disconnect the F16 airbag sensor assembly connector.

  1. Select "Communication Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    "Airbag" not displayed on intelligent tester.
    A
    Several ECUs and sensors other than "Airbag" not displayed on intelligent tester.
    B



B
Go to step 7
A


6.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)


    E186768E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F16-13 (CANH) - F16-22 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)

  1. Reconnect the F16 airbag sensor assembly connector.



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

7.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY))

HINT:
For vehicles without VSC, go to step 9.

  1. Disconnect the F30 steering angle sensor (spiral cable sub-assembly) connector.

  1. Select "Communication Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    "Spiral cable (Steering Angle Sensor)" not displayed on intelligent tester.
    A
    Several ECUs and sensors other than "Spiral cable (Steering Angle Sensor)" not displayed on intelligent tester.
    B



B
Go to step 9
A


8.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE)


    E186736E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F30-4 (CANH) - F30-3 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor (Spiral Cable Sub-assembly))

  1. Reconnect the F30 steering angle sensor (spiral cable sub-assembly) connector.



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE)
OK

REPLACE STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) (Click here)  

9.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
  1. Disconnect the F76 main body ECU (multiplex network body ECU) connector.

  1. Select "Communication Bus Check" on the intelligent tester (Click here).
    Result 
    Result
    Proceed to
    "Main Body" not displayed on intelligent tester.
    A
    Several ECUs and sensors other than "Main Body" not displayed on intelligent tester.
    B



B
Go to step 11
A


10.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE)
E217721E01
  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
F76-14 (CANH) - F76-13 (CANL)
Ignition switch off
54 to 69 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
  1. Reconnect the F76 main body ECU (multiplex network body ECU) connector.



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

11.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY BRANCH WIRE)
  1. Disconnect the F6 power steering ECU assembly connector.



    E217716E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F6-7 (CANH) - F6-8 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Steering ECU Assembly)
    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C

  1. Reconnect the F6 power steering ECU assembly connector.



B
REPLACE POWER STEERING ECU ASSEMBLY (Click here)

C
REPLACE POWER STEERING ECU ASSEMBLY (Click here)
A

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY BRANCH WIRE)