CAN COMMUNICATION SYSTEM (for Separate Type Yaw Rate Sensor) > Open in One Side of CAN Branch Line |
| Symptom | Trouble Area |
| 2 or more ECUs and/or sensors do not appear on the intelligent tester "CAN Bus Check" screen. |
|


| 1.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)) |
Disconnect the A54 skid control ECU (brake actuator assembly) connector.
Select "Communication Bus Check" on the intelligent tester (Click here).
| Result | Proceed to |
| "Skid Control (ABS/VSC/TRAC)" not displayed on intelligent tester. | A |
| Several ECUs and sensors other than "Skid Control (ABS/VSC/TRAC)" not displayed on intelligent tester. | B |
|
| ||||
| A | |
| 2.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A54-25 (CANH) - A54-14 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly)) |
Reconnect the A54 skid control ECU (brake actuator assembly) connector.
|
| ||||
| OK | ||
| ||
| 3.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY) |
Disconnect the F42*1 or F41*2 air conditioning amplifier assembly connector.
Select "Communication Bus Check" on the intelligent tester (Click here).
| Result | Proceed to |
| "Air Conditioning Amplifier" not displayed on intelligent tester. | A |
| Several ECUs and sensors other than "Air Conditioning Amplifier" not displayed on intelligent tester. | B |
|
| ||||
| A | |
| 4.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F42-11 (TX+) - F42-12 (TX-)*1 F41-8 (TX+) - F41-9 (TX-)*2 | Ignition switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector (to Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System)) |
| *b | Front view of wire harness connector (to Air Conditioning Amplifier Assembly (for Manual Air Conditioning System)) |
Reconnect the F42*1 or F41*2 air conditioning amplifier assembly connector.
|
| ||||
| OK | ||
| ||
| 5.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIRBAG SENSOR ASSEMBLY) |
Disconnect the F16 airbag sensor assembly connector.
Select "Communication Bus Check" on the intelligent tester (Click here).
| Result | Proceed to |
| "Airbag" not displayed on intelligent tester. | A |
| Several ECUs and sensors other than "Airbag" not displayed on intelligent tester. | B |
|
| ||||
| A | |
| 6.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F16-13 (CANH) - F16-22 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) |
Reconnect the F16 airbag sensor assembly connector.
|
| ||||
| OK | ||
| ||
| 7.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)) |
Disconnect the F30 steering angle sensor (spiral cable sub-assembly) connector.
Select "Communication Bus Check" on the intelligent tester (Click here).
| Result | Proceed to |
| "Spiral cable (Steering Angle Sensor)" not displayed on intelligent tester. | A |
| Several ECUs and sensors other than "Spiral cable (Steering Angle Sensor)" not displayed on intelligent tester. | B |
|
| ||||
| A | |
| 8.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F30-4 (CANH) - F30-3 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector (to Steering Angle Sensor (Spiral Cable Sub-assembly)) |
Reconnect the F30 steering angle sensor (spiral cable sub-assembly) connector.
|
| ||||
| OK | ||
| ||
| 9.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR) |
Disconnect the F122 yaw rate sensor connector.
Select "Communication Bus Check" on the intelligent tester (Click here).
| Result | Proceed to |
| "Yaw Rate / Deceleration Sensor" not displayed on intelligent tester. | A |
| Several ECUs and sensors other than "Yaw Rate / Deceleration Sensor" not displayed on intelligent tester. | B |
|
| ||||
| A | |
| 10.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F122-3 (CANH) - F122-2 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector (to Yaw Rate Sensor) |
Reconnect the F122 yaw rate sensor connector.
|
| ||||
| OK | ||
| ||
| 11.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) |
Disconnect the F76 main body ECU (multiplex network body ECU) connector.
Select "Communication Bus Check" on the intelligent tester (Click here).
| Result | Proceed to |
| "Main Body" not displayed on intelligent tester. | A |
| Several ECUs and sensors other than "Main Body" not displayed on intelligent tester. | B |
|
| ||||
| A | |
| 12.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F76-14 (CANH) - F76-13 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector (to Main Body ECU (Multiplex Network Body ECU)) |
Reconnect the F76 main body ECU (multiplex network body ECU) connector.
|
| ||||
| OK | ||
| ||
| 13.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY BRANCH WIRE) |
Disconnect the F6 power steering ECU assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F6-7 (CANH) - F6-8 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Rear view of wire harness connector (to Power Steering ECU Assembly) |
Reconnect the F6 power steering ECU assembly connector.
|
| ||||
| OK | ||
| ||