DTC B1637/82 Lost Communication with Rear Airbag Sensor LH |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1637/82 |
|
|


| 1.SYSTEM CHECK |
Check the vehicle specifications.
| Result | Proceed to |
| for 3 Door | A |
| for 5 Door | B |
|
| ||||
| A | |
| 2.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY LH |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Interchange the No. 2 side airbag sensor assembly LH with No. 2 side airbag sensor assembly RH and connect the connectors to them.
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
Connect the cable to the negative battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1632/81 and B1637/82 is not output. | A |
| DTC B1637/82 is output. | B |
| DTC B1632/81 is output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the No. 2 side airbag sensor assembly RH and the No. 2 side airbag sensor assembly LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| A | ||
| ||
| 3.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.
Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.
Check that the terminals of connectors are not damaged.
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (OPEN) |
Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

| *1 | No. 2 Side Airbag Sensor Assembly LH | *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire | *4 | Connector B |
| *5 | Connector C | *6 | Service Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) | *b | Front view of wire harness connector (to No. 2 Side Airbag Sensor Assembly LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K21-1 (BCL+) - K21-2 (BCL-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE (SHORT) |
![]() |
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K21-1 (BCL+) - K21-2 (BCL-) | Always | 1 MΩ or higher |
| *1 | No. 2 Side Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire |
| *4 | Connector B |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 6.CHECK FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| K21-1 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| K21-2 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | No. 2 Side Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire |
| *4 | Connector B |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 7.CHECK FLOOR WIRE (SHORT TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K21-1 (BCL+) - Body ground | Always | 1 MΩ or higher |
| K21-2 (BCL-) - Body ground | Always | 1 MΩ or higher |
| *1 | No. 2 Side Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly LH |
| *3 | Floor Wire |
| *4 | Connector B |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly LH) |
|
| ||||
| OK | |
| 8.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH |
![]() |
Connect the connectors to the No. 2 side airbag sensor assembly LH and airbag sensor assembly.
Interchange the side airbag sensor assembly LH with the side airbag sensor assembly RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1637/82 is output. | A |
| DTC B1632/81 is output. | B |
| DTCs B1632/81 or B1637/82 is not output. | C |
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the side airbag sensor assembly LH and the side airbag sensor assembly RH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| A | |
| 9.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY LH |
![]() |
Interchange the No. 2 side airbag sensor assembly LH with the No. 2 side airbag sensor assembly RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTCs B1632/81 or B1637/82 is not output. | A |
| DTC B1637/82 is output. | B |
| DTC B1632/81 is output. | C |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly LH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the No. 2 side airbag sensor assembly LH and the No. 2 side airbag sensor assembly RH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| A | ||
| ||