Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/ VSC/Separate Type Yaw Rate Sensor)

DTC    B1637/82    Lost Communication with Rear Airbag Sensor LH

for Preparation Click here


DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH) is composed of the airbag sensor assembly, side airbag sensor assembly LH (for 5 Door), door side airbag sensor LH (for 3 Door) and No. 2 side airbag sensor assembly LH.
The side airbag sensor assembly LH (for 5 Door), door side airbag sensor LH (for 3 Door) and No. 2 side airbag sensor assembly LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.
This DTC is stored when a malfunction is detected in the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).

DTC No.
DTC Detection Condition
Trouble Area
B1637/82
  1. The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).
  2. Side airbag sensor assembly LH malfunction (for 5 Door)
  3. No. 2 side airbag sensor assembly LH malfunction
  4. Airbag sensor assembly malfunction
  1. Floor wire
  2. Side airbag sensor assembly LH (for 5 Door)
  3. No. 2 side airbag sensor assembly LH
  4. Airbag sensor assembly

WIRING DIAGRAM


C241048E17


C241675E17


INSPECTION PROCEDURE

1.SYSTEM CHECK
  1. Check the vehicle specifications.
    Result 
    Result
    Proceed to
    for 3 Door
    A
    for 5 Door
    B



B
Go to step 3
A


2.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY LH


    C249132E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Interchange the No. 2 side airbag sensor assembly LH with No. 2 side airbag sensor assembly RH and connect the connectors to them.
    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly

  1. Connect the cable to the negative battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1632/81 and B1637/82 is not output.
    A
    DTC B1637/82 is output.
    B
    DTC B1632/81 is output.
    C

    HINT:
    DTCs other than B1632/81 and B1637/82 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the No. 2 side airbag sensor assembly RH and the No. 2 side airbag sensor assembly LH to their original positions and connect the connectors to them.



B
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE NO.2 SIDE AIRBAG SENSOR ASSEMBLY LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


4.CHECK FLOOR WIRE (OPEN)


  1. Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.


    C239812E15


    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly LH
    *2
    Side Airbag Sensor Assembly LH
    *3
    Floor Wire
    *4
    Connector B
    *5
    Connector C
    *6
    Service Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)
    *b
    Front view of wire harness connector
    (to No. 2 Side Airbag Sensor Assembly LH)

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K21-1 (BCL+) - K21-2 (BCL-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE
OK


5.CHECK FLOOR WIRE (SHORT)


    C240718E02
  1. Disconnect the service wire from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K21-1 (BCL+) - K21-2 (BCL-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly LH
    *2
    Side Airbag Sensor Assembly LH
    *3
    Floor Wire
    *4
    Connector B
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


6.CHECK FLOOR WIRE (SHORT TO B+)


    C240718E02
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    K21-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    K21-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V

    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly LH
    *2
    Side Airbag Sensor Assembly LH
    *3
    Floor Wire
    *4
    Connector B
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


7.CHECK FLOOR WIRE (SHORT TO GROUND)


    C240718E02
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K21-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    K21-2 (BCL-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly LH
    *2
    Side Airbag Sensor Assembly LH
    *3
    Floor Wire
    *4
    Connector B
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


8.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    C249132E01
  1. Connect the connectors to the No. 2 side airbag sensor assembly LH and airbag sensor assembly.

  1. Interchange the side airbag sensor assembly LH with the side airbag sensor assembly RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1637/82 is output.
    A
    DTC B1632/81 is output.
    B
    DTCs B1632/81 or B1637/82 is not output.
    C
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly

    HINT:
    Codes other than DTCs B1632/81 and B1637/82 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly LH and the side airbag sensor assembly RH to their original positions and connect the connectors to them.



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


9.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY LH


    C166174E16
  1. Interchange the No. 2 side airbag sensor assembly LH with the No. 2 side airbag sensor assembly RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTCs B1632/81 or B1637/82 is not output.
    A
    DTC B1637/82 is output.
    B
    DTC B1632/81 is output.
    C
    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly LH

    HINT:
    Codes other than DTCs B1632/81 and B1637/82 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the No. 2 side airbag sensor assembly LH and the No. 2 side airbag sensor assembly RH to their original positions and connect the connectors to them.



B
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE NO.2 SIDE AIRBAG SENSOR ASSEMBLY LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)