Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY (for 3 Door)

FRONT SEAT OUTER BELT ASSEMBLY (for 3 Door) > INSTALLATION

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.



1. INSTALL FRONT SEAT OUTER BELT ASSEMBLY


    B225046E03
  1. Check the angle of inclination required to lock the retractor.

    1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15 ° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45 ° or more.
      Text in Illustration 
      *a
      Unlock
      *b
      Lock

      NOTICE:
      Do not disassemble the retractor.

      If the operation is not as specified, replace the front seat outer belt assembly.



    B282673E01
  1. Engage the 2 hooks and temporarily install the front seat outer belt assembly with the 2 bolts.

  1. Tighten bolt A and then bolt B.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf } for bolt A
    41 N*m{ 420 kgf*cm , 30 ft.*lbf } for bolt B



    B282675E01
  1. Connect the pretensioner connector.
    Text in Illustration 
    *1
    Locking Button

  1. Lock the locking button.

    NOTICE:
    Securely lock the locking button.

  1. Install the shoulder anchor part of the front seat outer belt assembly with the bolt.

    Torque:
    41 N*m{ 420 kgf*cm , 30 ft.*lbf }

  1. Connect the floor anchor part of the front seat outer belt assembly and install the front seat belt outer bar sub-assembly with the 2 bolts.

    Torque:
    41 N*m{ 420 kgf*cm , 30 ft.*lbf }

  1. Check that the ELR locks.

    NOTICE:
    The check should be performed with the front seat outer belt installed.


    1. With the belt installed, check that the belt locks when it is pulled out quickly.

      NOTICE:
      If the operation is not as specified, replace the front seat outer belt assembly.

  1. Remove the 2 bolts and the front seat belt outer bar sub-assembly, disconnect the floor anchor part of the front seat outer belt assembly .



2. INSTALL CENTER PILLAR UPPER GARNISH
  1. Pass the front seat outer belt through the slit in the center pillar upper garnish.

  1. Engage the clip and install the center pillar upper garnish with 2 screws.



3. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY
  1. Engage the 8 clips and the 10 claws.

  1. Engage the 3 guides and install the quarter trim panel.



4. INSTALL FRONT SEAT BELT OUTER BAR SUB-ASSEMBLY
  1. Connect the floor anchor part of the front seat outer belt assembly and install the front seat belt outer bar sub-assembly with the 2 bolts.

    Torque:
    41 N*m{ 420 kgf*cm , 30 ft.*lbf }



5. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP


    B284341E01
  1. Align the paint mark on the front door opening trim weatherstrip with the flange position on the vehicle body and install the weatherstrip.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Flange Position

    Paint Mark:
    Area
    Color
    RH Side
    Yellow
    LH Side
    White

    NOTICE:
    After installation, check that the corners fit correctly.



6. INSTALL FRONT DOOR SCUFF PLATE
  1. Engage the 8 claws and install the front door scuff plate.



7. INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)
(Click here)


8. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
(Click here)


9. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
(Click here)


10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



11. INSPECT SRS WARNING LIGHT
(Click here)