Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY (for 5 Door)

FUEL LID LOCK CONTROL CABLE ASSEMBLY (for 5 Door) > REMOVAL

for Preparation Click here



1. REMOVE DECK BOARD ASSEMBLY


    B272608
  1. Remove the deck board.



2. REMOVE SPARE WHEEL COVER


    B272609
  1. Remove the spare wheel cover.



3. REMOVE FRONT SEAT ASSEMBLY (for Driver Side)
(Click here)


4. REMOVE FRONT SEAT ASSEMBLY (for Front Passenger Side)
(Click here)


5. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
(Click here)


6. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
(Click here)


7. REMOVE REAR SEAT ASSEMBLY (for Fold Down Seat Type)
(Click here)


8. REMOVE REAR CONSOLE BOX ASSEMBLY
(Click here)


9. REMOVE FRONT DOOR SCUFF PLATE RH


    B272611
  1. Disengage the 8 claws and remove the front door scuff plate.



10. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



11. REMOVE COWL SIDE TRIM BOARD RH


    B284314
  1. Remove the clip.

  1. Disengage the clip and remove the cowl side trim board.



12. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



13. REMOVE REAR DOOR SCUFF PLATE RH


    B272618
  1. Disengage the 5 claws and guide and remove the rear door scuff plate.



14. REMOVE REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



15. REMOVE REAR FLOOR FINISH PLATE


    B272624
  1. Disengage the 4 claws and 4 guides and remove the rear floor finish plate.



16. SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side



17. SEPARATE REAR DOOR OPENING TRIM WEATHERSTRIP
  1. Separate the rear door opening trim weatherstrip.



18. REMOVE NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)


    E222045E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw.
    Text in Illustration 
    *1
    Protective Tape

  1. Disconnect the connector and remove the No. 2 room light assembly.



19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

HINT:
Use the same procedure as for the RH side



20. REMOVE JACK COVER


21. REMOVE JACK ASSEMBLY


22. REMOVE FRONT FLOOR CARPET ASSEMBLY
  1. Disengage the 6 clamps.

  1. Remove the clip and front floor carpet.



23. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    B284622
  1. Remove the bolt.

  1. Slide the fuel lid lock open lever as indicated by the arrow as shown in the illustration.



    B284621
  1. Disengage the guide and separate the fuel lid lock control cable.



24. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for LHD)


    B266731
  1. Disengage the 2 claws and separate the fuel lid lock control cable.



  1. Disengage the 4 clamps and remove the fuel lid lock control cable as shown in the illustration.


    B284618E01


    Text in Illustration 
    *1
    Fuel Lid Lock Control Cable Sub-assembly
    *2
    Wire Harness Clamp



25. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for RHD)


    B266731
  1. Disengage the 2 claws and separate the fuel lid lock control cable.



  1. Disengage the 7 clamps and remove the fuel lid lock control cable as shown in the illustration.


    B271663E01


    Text in Illustration 
    *1
    Fuel Lid Lock Control Cable Sub-assembly
    *2
    Wire Harness Clamp



26. REMOVE FUEL FILLER OPENING LID LOCK RETAINER


    B266728E01
  1. Rotate the fuel filler opening lid lock retainer by 90° and disengage the 2 claws A from the 2 slits as shown in the illustration.
    Text in Illustration 
    *1
    Claw A
    *a
    Slit
    *b
    Rotate



    B266729E01
  1. Rotate the fuel filler opening lid lock retainer by another 90° and remove it by disengaging the 2 claws B from the 2 slits as shown in the illustration.
    Text in Illustration 
    *1
    Claw B
    *a
    Slit
    *b
    Rotate