Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY (for 3 Door)

FUEL LID LOCK CONTROL CABLE ASSEMBLY (for 3 Door) > REMOVAL

for Preparation Click here



1. REMOVE DECK BOARD ASSEMBLY


    B272608
  1. Remove the deck board.



2. REMOVE SPARE WHEEL COVER


    B272609
  1. Remove the spare wheel cover.



3. REMOVE FRONT SEAT ASSEMBLY (for Driver Side)
(Click here)


4. REMOVE FRONT SEAT ASSEMBLY (for Front Passenger Side)
(Click here)


5. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)
(Click here)


6. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)
(Click here)


7. REMOVE REAR SEAT ASSEMBLY (for Fold Down Seat Type)
(Click here)


8. REMOVE REAR CONSOLE BOX
(Click here)


9. REMOVE FRONT DOOR SCUFF PLATE RH


    B284313
  1. Disengage the 8 claws and remove the front door scuff plate.



10. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



11. REMOVE COWL SIDE TRIM BOARD RH


    B284314
  1. Remove the clip.

  1. Disengage the clip and remove the cowl side trim board.



12. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



13. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Separate the front door opening trim weatherstrip.



14. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Separate the front door opening trim weatherstrip.



15. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY RH


    B282674
  1. Remove the 2 bolts and front seat belt outer bar sub-assembly, disconnect the floor anchor part of the front seat outer belt assembly.



16. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



17. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH


    B284318
  1. Disengage the 8 clips and 10 claws.

  1. Disengage the 3 guides and remove the quarter trim panel.



18. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



19. REMOVE REAR FLOOR FINISH PLATE


    B272624
  1. Disengage the 4 claws and 4 guides and remove the rear floor finish plate.



20. SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH


    B284323
  1. Remove the bolt.

  1. Disengage the 2 claws and separate the rear seat 3 point type outer belt.



21. SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



22. REMOVE NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)


    E222045E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw.
    Text in Illustration 
    *1
    Protective Tape

  1. Disconnect the connector and remove the No. 2 room light assembly.



23. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

HINT:
Use the same procedure as for the RH side .



24. REMOVE JACK COVER


25. REMOVE JACK ASSEMBLY


26. REMOVE FRONT FLOOR CARPET ASSEMBLY
  1. Disengage the 6 clamps.

  1. Remove the clip and front floor carpet.



27. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    B284622
  1. Remove the bolt.

  1. Slide the fuel lid lock open lever as indicated by the arrow as shown in the illustration.



    B284621
  1. Disengage the guide and separate the fuel lid lock control cable.



28. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for LHD)


    B266731
  1. Disengage the 2 claws and separate the fuel lid lock control cable.



  1. Disengage the 4 clamps and remove the fuel lid lock control cable as shown in the illustration.


    B284620E01


    Text in Illustration 
    *1
    Fuel Lid Lock Control Cable Sub-assembly
    *2
    Wire Harness Clamp



29. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for RHD)


    B266731
  1. Disengage the 2 claws and separate the fuel lid lock control cable.



  1. Disengage the 7 clamps and remove the fuel lid lock control cable as shown in the illustration.


    B284619E01


    Text in Illustration 
    *1
    Fuel Lid Lock Control Cable Sub-assembly
    *2
    Wire Harness Clamp



30. REMOVE FUEL FILLER OPENING LID LOCK RETAINER


    B266728E01
  1. Rotate the fuel filler opening lid lock retainer by 90° and disengage the 2 claws A from the 2 slits as shown in the illustration.
    Text in Illustration 
    *1
    Claw A
    *a
    Slit
    *b
    Rotate



    B266729E01
  1. Rotate the fuel filler opening lid lock retainer by another 90° and remove it by disengaging the 2 claws B from the 2 slits as shown in the illustration.
    Text in Illustration 
    *1
    Claw B
    *a
    Slit
    *b
    Rotate