Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Separate Type Yaw Rate Sensor)

DTC    C1436    Yaw Rate Sensor Malfunction

for Preparation Click here


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and deceleration sensor (yaw rate sensor) via the CAN communication system.
The yaw rate and deceleration sensor (yaw rate sensor) has a built in deceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate and deceleration sensor (yaw rate sensor) and the CAN communication system, the DTCs U0123 (Lost Communication with Yaw Rate Sensor Module) and U0124 (Lost Communication with Lateral Acceleration Sensor Module) are output.
These DTCs are also output when calibration has not been completed.

DTC No.
DTC Detection Condition
Trouble Area
C1436
Either of the following is detected:
  1. With the vehicle stationary, the yaw rate and deceleration sensor output value is not 0 deg/s.
  2. Abnormal comparison value.
Yaw rate and deceleration sensor (Yaw rate sensor)

WIRING DIAGRAM

Refer to DTCs C1232, C1243 and C1245 .

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the brake actuator assembly, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When DTC U0123, U0124 and/or U0126 is output together with DTC C1436, inspect and repair the trouble areas indicated by DTC U0123, U0124 and/or U0126 first (Click here).

1.READ VALUE USING INTELLIGENT TESTER (YAW RATE SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the tester, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Yaw Rate Sensor
    Yaw rate sensor/min.: -128°/s, max.: 127°/s
    0°/s: Vehicle stopped
    -128 to 0°/s: Turning right
    0 to 127°/s: Turning left
    -

  1. Check that the yaw rate and deceleration sensor (yaw rate sensor) output value displayed on the intelligent tester.

    Result 
    Result
    Proceed to
    NG (The yaw rate and deceleration sensor (yaw rate sensor) output value is 0 deg/s when the vehicle is stationary, but the value fluctuates when turning)
    A
    NG (The yaw rate and deceleration sensor (yaw rate sensor) output value is not 0 deg/s when the vehicle is stationary)
    B
    OK
    C

    NOTICE:
    Check the yaw rate and deceleration sensor (yaw rate sensor) signal after replacement (Click here).

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR) (Click here)

C
CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)
A


2.CHECK YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR) INSTALLATION
  1. Turn the ignition switch off.

  1. Check that the yaw rate and deceleration sensor (yaw rate sensor) has been installed properly (Click here).

    OK:
    The sensor should be tightened to the specified torque.
    The sensor should not be installed in a tilted position.

    NOTICE:
    Check the yaw rate and deceleration sensor (yaw rate sensor) signal after replacement (Click here).

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
INSTALL YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR) CORRECTLY (Click here)
OK

REPLACE YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR) (Click here)