VEHICLE STABILITY CONTROL SYSTEM (for Separate Type Yaw Rate Sensor) > TEST MODE PROCEDURE |
| WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK |
Release the parking brake.
When the ignition switch is turned to ON, check that the ABS warning, brake warning, VSC OFF indicator and TRC OFF indicator, Slip indicator lights come on for approximately 3 seconds.
| Trouble Area | See Procedure |
| ABS warning light circuit (Remains on) |
Click here
|
| ABS warning light circuit (Does not come on) |
Click here
|
| Brake warning light circuit (Remains on) |
Click here
|
| Brake warning light circuit (Does not come on) |
Click here
|
| TRC OFF indicator light circuit (Remains on) |
Click here
|
| TRC OFF indicator light circuit (Does not come on) |
Click here
|
| VSC OFF indicator light circuit (Remains on) |
Click here
|
| VSC OFF indicator light circuit (Does not come on) |
Click here
|
| Slip indicator light circuit (Remains on) |
Click here
|
| Slip indicator light circuit (Does not come on) |
Click here
|
| SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using Intelligent Tester) |
Procedure to enter Test Mode.
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
Check that the shift lever is in neutral and apply the parking brake.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Switch the skid control ECU (brake actuator assembly) to Test Mode using the intelligent tester.
Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.
Check that the ABS warning and Slip indicator lights come on for several seconds and then blink in the Test Mode blinking pattern.
| Trouble Area | See Procedure |
| TS and CG terminal circuit |
Click here
|
| ABS warning light circuit (Remains on) |
Click here
|
| ABS warning light circuit (Does not come on) |
Click here
|
| Slip indicator light circuit (Remains on) |
Click here
|
| Slip indicator light circuit (Does not come on) |
Click here
|
| DECELERATION SENSOR CHECK (When Using Intelligent Tester) |
Keep the vehicle stationary on a level surface for 1 second or more.
| MASTER CYLINDER PRESSURE SENSOR CHECK (When Using Intelligent Tester) |
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly and continuously depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.
Check that the ABS warning light stays on for 3 seconds.
| SPEED SENSOR CHECK (When Using Intelligent Tester) |
Check the speed sensor signal.
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
| VSC OFF SWITCH CHECK |
Briefly press the VSC OFF switch.
Check that the VSC OFF indicator light on.
Briefly press the VSC OFF switch again to turn the VSC OFF indicator light off.
| END OF SENSOR CHECK (When Using Intelligent Tester) |
If the sensor check is completed, the ABS warning light blinks and Slip indicator blinks (Test Mode) when the vehicle stops and the ABS warning light is off while the vehicle is being driven.
| READ DTC OF SIGNAL CHECK FUNCTION (When Using Intelligent Tester) |
Read the DTC(s) by following the tester screen.
List of DTCs.
| DTC Code | Detection Item | Trouble Area |
| C1271 | Low output signal from front speed sensor RH |
|
| C1272 | Low output signal from front speed sensor LH |
|
| C1273 | Low output signal from rear speed sensor RH |
|
| C1274 | Low output signal from rear speed sensor LH |
|
| C1275 | Abnormal change in output signal from front speed sensor RH | Speed sensor rotor |
| C1276 | Abnormal change in output signal from front speed sensor LH | Speed sensor rotor |
| C1277 | Abnormal change in output signal from rear speed sensor RH | Speed sensor rotor |
| C1278 | Abnormal change in output signal from rear speed sensor LH | Speed sensor rotor |
| C1279 | Deceleration sensor output voltage malfunction |
|
| C1281 | Master cylinder pressure sensor output malfunction |
|
| DTC Code | Detection Item | Trouble Area |
| C1473 | Yaw rate sensor | Yaw rate and deceleration sensor (yaw rate sensor) |
Turn the ignition switch off and disconnect the intelligent tester.
| SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When not Using Intelligent Tester) |
Procedure to enter Test Mode.
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
Check that the shift lever is in neutral and apply the parking brake.
![]() |
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
| *a | Front view of DLC3 |
Turn the ignition switch to ON.
Check that the ABS warning and Slip indicator lights come on for several seconds and then blink in Test Mode.
| Trouble Area | See Procedure |
| TS and CG terminal circuit |
Click here
|
| ABS warning light circuit (Remains on) |
Click here
|
| ABS warning light circuit (Does not come on) |
Click here
|
| Slip indicator light circuit (Remains on) |
Click here
|
| Slip indicator light circuit (Does not come on) |
Click here
|
| *a | Blinking Pattern in Test Mode |
| *b | 0.125 Seconds |
| DECELERATION SENSOR CHECK (When not Using Intelligent Tester) |
Keep the vehicle stationary on a level surface for 1 second or more.
| MASTER CYLINDER PRESSURE SENSOR CHECK (When not Using Intelligent Tester) |
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly and continuously depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.
Check that the ABS warning light stays on for 3 seconds.
| SPEED SENSOR CHECK (When not Using Intelligent Tester) |
Check the speed sensor signal.
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
| VSC OFF SWITCH CHECK |
Briefly press the VSC OFF switch.
Check that the VSC OFF indicator light on.
Briefly press the VSC OFF switch again to turn the VSC OFF indicator light off.
| END OF SENSOR CHECK (When not Using Intelligent Tester) |
If the sensor check is completed, the ABS warning light blinks and Slip indicator blinks (Test Mode) when the vehicle stops and the ABS warning light is off while the vehicle is being driven.
| READ DTC OF SIGNAL CHECK FUNCTION (When not Using Intelligent Tester) |
![]() |
Using SST, connect terminals 12 (TS), 13 (TC) and 4 (CG) of the DLC3.
| *a | Front view of DLC3 |
Count the number of blinks of the ABS warning and VSC OFF indicator lights.
After performing the check, disconnect SST from terminals TS and CG, and TC and CG of the DLC3 and turn the ignition switch off.
Turn the ignition switch to ON.
| DTC OF TEST MODE (SIGNAL CHECK) FUNCTION (Procedure "A") |
| DTC Code | Detection Item | Trouble Area |
| 71 | Low output signal from front speed sensor RH |
|
| 72 | Low output signal from front speed sensor LH |
|
| 73 | Low output signal from rear speed sensor RH |
|
| 74 | Low output signal from rear speed sensor LH |
|
| 75 | Abnormal change in output signal from front speed sensor RH | Speed sensor rotor |
| 76 | Abnormal change in output signal from front speed sensor LH | Speed sensor rotor |
| 77 | Abnormal change in output signal from rear speed sensor RH | Speed sensor rotor |
| 78 | Abnormal change in output signal from rear speed sensor LH | Speed sensor rotor |
| 79 | Deceleration sensor output voltage malfunction |
|
| 81 | Master cylinder pressure sensor output malfunction |
|
| DTC Code | Detection Item | Trouble Area |
| 71 | Yaw rate sensor | Yaw rate and deceleration sensor (yaw rate sensor) |