Scan Tool Data
Precautions: General safety (00)
ECM
NOTE:
•If communication between SUZUKI scan tool and ECM is not possible, perform the following checks:
•With the generic scan tool, only data with asterisk (*) in the following table can be read. (type A, C, D and E)
•When checking data with engine running at idle or racing, place gear shift lever in neutral position and apply parking brake lever fully. Also, if nothing or “no load” is indicated, turn off A/C, all electric loads, P/S and all the other switches.
•Data with asterisk 1 (*1) in the table below is applicable to type A and E.
—Check communication condition between PC and VCI using SUZUKI scan tool function.
—Check DLC power circuit and ground circuit.
—Check DLC cable. If necessary, check DLC cable by substituting a known-good DLC cable.
—Check CAN communication system. (“Control Module Communication Bus Off” is detected in any control module.)
—Check ECM power circuit and ground circuit.
•For type distinction of OBD system, refer to “Discrimination for OBD System” under OBD System Description:M16A.—Check DLC power circuit and ground circuit.
—Check DLC cable. If necessary, check DLC cable by substituting a known-good DLC cable.
—Check CAN communication system. (“Control Module Communication Bus Off” is detected in any control module.)
—Check ECM power circuit and ground circuit.
•With the generic scan tool, only data with asterisk (*) in the following table can be read. (type A, C, D and E)
•When checking data with engine running at idle or racing, place gear shift lever in neutral position and apply parking brake lever fully. Also, if nothing or “no load” is indicated, turn off A/C, all electric loads, P/S and all the other switches.
•Data with asterisk 1 (*1) in the table below is applicable to type A and E.
| Scan tool data | Vehicle condition | Normal condition / Reference value | |
|---|---|---|---|
| * | Fuel System
|
Open loop control before satisfaction of closed loop control conditions (ECT >10 °C, IAT, TP, A/F sensor/system = OK) | OL (open loop) |
| Open loop control due to driving conditions (Power enrichment, etc.) | OL-Drive (open loop) | ||
| Open loop control due to system fault detected | OL-Fault (open loop) | ||
| Closed loop control using HO2S-1 and HO2S-2 sensor as feedback sensors for fuel control | CL (closed loop) | ||
| Closed loop control due to system fault detected | CL-Fault (closed loop) | ||
| When engine stops with ignition “ON” | — | ||
| * | Short Term Fuel Trim
|
Engine: Idle speed after warming up | Approx. –20 to 20% |
| * | Long Term Fuel Trim
|
Engine: Idle speed after warming up | Approx. –20 to 20% |
| Total Fuel Trim
|
Engine: Idle speed after warming up | Approx. –30 to 30% | |
| Inj Pulse Width
|
Engine: Idle speed with no load after warming up | Approx. 1.6 to 4.0 msec. | |
| * | Ignition Advance
|
Engine: Idle speed with no load after warming up | 1 to 15° BTDC |
| * | Calculated Load
|
Engine: Idle speed with no load after warming up | Approx. 20 to 40% |
| * | Engine Speed
|
Engine: Idle speed after warming up Radiator cooling fan: Stopped All electrical equipment: OFF Gear shift lever: Neutral position (M/T model) Select lever: P range (A/T model) |
M/T model: 550 to 650 rpm A/T model: 600 to 700 rpm |
| Desired Idle
|
Engine: Idle speed after warming up Radiator cooling fan: Stopped All electrical equipment: OFF Gear shift lever: Neutral position (M/T model) Select lever: P range (A/T model) |
M/T model: 550 to 650 rpm A/T model: 600 to 700 rpm |
|
| * | Vehicle Speed
|
Vehicle running | Almost the same as speedometer reading |
| * | MAP
|
Engine: Idle speed after warming up | Approx. 20 to 55 kPa |
| * | ECT
|
Engine: Idle speed after warming up | Approx. 80 to 105 °C (176 – 221 °F) |
| * | Intake Air Temperature
|
Engine: Idle speed after warming up | –5 °C (–9 °F) + environmental temperature to 40 °C (72 °F) + environmental temperature |
| * | Barometric Pres
|
— | Barometric pressure is displayed. |
| * | EVAP Canist Prg Duty
|
Engine: Idle speed after warming up | 0% |
| VVT Gap
|
Engine: Idle speed after warming up | –1.0 to 1.0° CA | |
| IAC Throttle Opening
|
Engine: Idle speed with no load after warming up | Approx. 1 to 40% | |
| Engine: Idle speed after warming up A/C compressor: Operating Blower speed selector: Max position |
Approx. 10 to 50% | ||
| TP Sensor 1 Volt
|
Ignition: “ON” Accelerator pedal: Released |
0.6 to 1.0 V | |
| Ignition: “ON” Accelerator pedal: Fully depressed |
4.1 to 4.5 V | ||
| TP Sensor 2 Volt
|
Ignition: “ON” Accelerator pedal: Released |
4.0 to 4.4 V | |
| Ignition: “ON” Accelerator pedal: Fully depressed |
0.5 to 0.9 V | ||
| APP Sensor 1 Volt
|
Ignition: “ON” Accelerator pedal: Released |
0.6 to 0.9 V | |
| Ignition: “ON” Accelerator pedal: Fully depressed |
3.7 to 4.4 V | ||
| APP Sensor 2 Volt
|
Ignition: “ON” Accelerator pedal: Released |
0.3 to 0.5 V | |
| Ignition: “ON” Accelerator pedal: Fully depressed |
1.8 to 2.2 V | ||
| * | Accel Position
|
Ignition: “ON” Accelerator pedal: Released |
0 to 2% |
| Ignition: “ON” Accelerator pedal: Fully depressed |
90 to 100% | ||
| * | Throttle Position
|
Ignition: “ON” Accelerator pedal: Released |
0 to 10% |
| Ignition: “ON” Accelerator pedal: Fully depressed |
90 to 100% | ||
| * | Target Throttle Posi
|
Ignition: “ON” Accelerator pedal: Released |
0 to 2% |
| Ignition: “ON” Accelerator pedal: Fully depressed |
90 to 100% | ||
| * | O2S B1 S1
|
Engine: Idle speed after warming up | Approx. 0 to 1.0 V |
| * | O2S B1 S2
|
Engine: 2,000 rpm for 3 min. or more after warming up | Approx. 0 to 1.0 V |
| * | Battery Voltage
|
Engine: Idle speed | Approx. 13 to 15 V |
| Fuel Tank Level
|
Ignition: “ON” | 0 to 100% | |
| A/C Pressure
|
Engine: Idle speed A/C compressor: Operating Blower speed selector: Max position Ambient temperature: 30 °C (86 °F) |
HFC–134a: 1,400 to 1,730 kPa HFO–1234yf: 1,270 to 1,630 kPa |
|
| Generator Reg Volt (Com)
|
Engine: Idle speed | 12.0 to 15.0 V | |
| Radiator Fan
|
Radiator cooling fan: Off | Off | |
| Radiator cooling fan: Low speed | Low | ||
| Radiator cooling fan: High speed | High | ||
| A/C Comp Relay
|
Engine: Running A/C compressor: Operating Blower speed selector: 1st or higher speed position |
ON | |
| Other than above condition | OFF | ||
| Fuel Pump
|
Engine: Running | ON | |
| Other than above condition | OFF | ||
| |
Intake Tuning Sol (Com)
|
IMT valve: Close (using “IMT Valve” of “Active Test” mode on SUZUKI scan tool.) | Close |
| IMT valve: Open (using “IMT Valve” of “Active Test” mode on SUZUKI scan tool.) | Open | ||
| Starter SW
|
Ignition: “START” (engine cranking) | ON | |
| Other than above condition | OFF | ||
| A/C Switch
|
A/C switch: ON | ON | |
| Other than above condition | OFF | ||
| Blower Fan
|
Non-A/C model: 2nd or higher speed position Manual A/C model: 2nd or higher speed position Auto A/C model: 4th or higher speed position |
ON | |
| Non-A/C model: Other than above condition Manual A/C model: Other than above condition Auto A/C model: Other than above condition |
OFF | ||
| Brake Switch
|
Brake pedal: Depressed | ON | |
| Brake pedal: Released | OFF | ||
| Electric Load
|
Headlight: ON | ON | |
| Headlight: OFF | OFF | ||
| PNP Signal
|
Select lever: P or N range | P/N | |
| Select lever: Other than P or N range | D | ||
| Clutch SW
|
Clutch pedal: Depressed fully | Declutch | |
| Clutch pedal: Released | Clutched | ||
| Cruise RES/ACC Switch
|
“RES / +” switch: Pushed | ON | |
| “RES / +” switch: Released | OFF | ||
| Cruise SET/COAST Switch
|
“SET / –” switch: Pushed | ON | |
| “SET / –” switch: Released | OFF | ||
| Cruise CANCEL Switch
|
“CANCEL” switch: Pushed | ON | |
| “CANCEL” switch: Released | OFF | ||
| Cruise ON/OFF Switch
|
“Cruise” switch: Pushed | Pushed | |
| “Cruise” switch: Released | Released | ||
| Distance Setting Switch
|
Distance switch: Pushed | ON | |
| Distance switch: Released | OFF | ||
| Fuel Cut
|
Engine: Idle speed after warming up | OFF | |
| Accelerator pedal: Released Engine condition: 2,000 rpm or more after warming up |
ON | ||
| Closed Throttle Pos
|
Ignition: “ON” Accelerator pedal: Released |
ON | |
| Ignition: “ON” Accelerator pedal: Fully depressed |
OFF | ||
| O2S B1 S1 Act
|
Engine: Idle speed after warming up | Active | |
| O2S B1 S2 Act
|
Engine: Idle speed after warming up | Active | |
| IMT Valve Actuator
|
IMT valve: Close (using “IMT Valve” of “Active Test” mode on SUZUKI scan tool.) | Close | |
| IMT valve: Open (using “IMT Valve” of “Active Test” mode on SUZUKI scan tool.) | Open | ||
| ENG A-STOP (Mon) (*1)
|
Engine is stopped by engine auto stop control. | Eng Stop | |
| Other than above condition | Eng Run | ||
| ENG A-STOP (Com) (*1)
|
ENG A-STOP control module requests engine auto-stop | Req | |
| Engine: Running | Not Req |
Scan Tool Data Definitions
Fuel System (Fuel system status)
A/F ratio feedback loop status is displayed as follows.
OL: Open loop control before satisfaction of closed loop control conditions (ECT > 10 °C, IAT, TP sensor/system = OK).
CL: Closed loop control using oxygen sensor(s) as feedback sensor(s).
OL-DRIVE: Open loop control due to driving requirement (power-up enrichment etc.).
OL-FAULT: Open loop control system fault.
CL-FAULT: Closed loop control system fault.
Short Term Fuel Trim (%)
Short term fuel trim value represents short term corrections to air/fuel mixture. 0 (zero) indicates no correction, a value greater than 0 indicates enrichment correction, and a value less than 0 indicates enleanment correction.
Long Term Fuel Trim (%)
Long term fuel trim value represents long term corrections to air/fuel mixture. 0 (zero) indicates no correction, a value greater than 0 indicates enrichment correction, and a value less than 0 indicates enleanment correction.
Total Fuel Trim (%)
Total fuel trim is calculated from short term fuel trim and long term fuel trim. This value indicates how much correction is necessary to keep the air/fuel mixture stoichiometrical.
Inj Pulse Width (Fuel injection pulse width, msec)
This parameter indicates the injector drive pulse width (time) during which the injector valve stays open as commanded by ECM. (For multipoint fuel injection, the injector drive time means that of the No.1 cylinder.)
Ignition Advance (Ignition timing advance for No.1 cylinder, ° BTDC)
This parameter indicates the ignition timing of No.1 cylinder commanded by ECM. The actual ignition timing should be checked using a timing light.
Calculated Load (Calculated load value, %)
This parameter indicates calculated engine load in percent. The load is calculated based on input signals to ECM from various engine sensors.
Engine Speed (rpm)
The engine speed is calculated from reference pulses from the camshaft position sensor.
Desired Idle (Desired idle speed, rpm)
The desired idle speed is an ECM internal parameter which indicates the idle speed requested by ECM. If the engine is not running, this number is not valid.
Vehicle Speed (km/h, MPH)
The vehicle speed is calculated based on pulse signals from wheel speed sensors.
MAP (Manifold absolute pressure, kPa, mmHg, in.Hg, psi, inH2O)
This parameter indicates the calculated manifold pressure based on MAP sensor signal.
ECT (Engine coolant temperature, °C, °F)
It is detected by engine coolant temperature sensor.
Intake Air Temperature. (°C, °F)
It is detected by intake air temperature sensor.
Barometric Pres (Barometric pressure, kPa, mmHg, in.Hg, psi, inH2O)
This parameter represents barometric air pressure measurement and is used for altitude correction of the fuel injection rate.
Evap Canist Prg Duty (Evap canister purge flow duty, %)
This parameter indicates valve ON (valve open) time rate within a certain set cycle of EVAP canister purge valve which controls the amount of EVAP purge.
VVT Gap (Variable valve timing difference between target and actual position, °)
This parameter indicates difference between target camshaft position (intake side) and actual camshaft position (intake side).
IAC Throttle Opening (Idle air throttle valve opening, %)
This parameter indicates throttle valve opening of idle air control in % (100% indicates the maximum idle air flow).
TP Sensor 1 Volt (TP sensor (main) output voltage, V)
TP Sensor (Main) data provides throttle valve opening information in the form of voltage.
TP Sensor 2 Volt (TP sensor (sub) output voltage, V)
TP Sensor (Sub) data provides throttle valve opening information in the form of voltage.
APP Sensor 1 Volt (APP sensor (main) output voltage, V)
APP sensor (main) data provides accelerator pedal position information in the form of voltage.
APP Sensor 2 Volt (APP sensor (sub) output voltage, V)
APP sensor (sub) data provides accelerator pedal position information in the form of voltage.
Accel Position (Absolute accelerator pedal position, %)
This parameter indicates calculated accelerator pedal position in percent based on input from accelerator pedal position sensor.
Throttle Position (Absolute throttle position, %)
This parameter indicates calculated throttle opening in percent based on input from throttle position sensor.
Target Throttle Posi (Target throttle valve position, %)
Target throttle valve position is an ECM internal parameter which indicates the throttle valve position requested by ECM.
O2S B1 S1 (HO2S-1, V)
This parameter indicates output voltage of HO2S-1 installed on exhaust manifold (pre-TWC).
O2S B1 S2 (HO2S-2, V)
This parameter indicates output voltage of HO2S-2 installed on exhaust No.1 pipe (post-TWC). It is used to detect catalyst deterioration.
Battery Voltage (V)
This parameter indicates battery voltage inputted from main relay to ECM.
Fuel Tank Level (%)
This parameter indicates approximate fuel level in the fuel tank. The fuel level data is provided in percentage from 0 to 100%.
A/C Pressure (A/C refrigerant absolute pressure, kPa)
This parameter indicates A/C refrigerant absolute pressure detected by A/C refrigerant pressure sensor.
Generator Reg Volt (Com) (Generator Regulated Voltage (Com) (V))
This parameter indicates commanded regulated-voltage to generator.
Radiator Fan (Radiator cooling fan control relay, Low/High/Off)
Low: ON command is being output to the radiator cooling fan relay No.1.
High: ON command is being output to radiator cooling fan relays No.2 and No.3.
Off: No command is being output.
A/C Comp Relay (A/C compressor relay, ON/OFF)
This parameter indicates the state of the A/C compressor relay.
Fuel Pump (ON/OFF)
ON is displayed when ECM activates the fuel pump via the fuel pump relay switch.
Intake Tuning Sol (Com) (IMT valve actuator control command, Open / Close)
Open: Open command is being output to IMT valve actuator.
Close: Close command is being output to IMT valve actuator.
Starter SW (Starter switch, ON/OFF)
This parameter indicates state of starting motor control relay output.
ON: Starting motor control relay is on.
OFF: Starting motor control relay is off.
A/C Switch (ON/OFF)
ON: Command for A/C operation is being output from HVAC to ECM.
OFF: Command for A/C operation is not being output.
Blower Fan (ON/OFF)
This parameter indicates the state of the blower speed selector.
Brake Switch (ON/OFF)
This parameter indicates the state of the brake switch.
Electric Load (ON/OFF)
ON: ON signal of headlight, clearance lights or rear end door window defogger is input.
OFF: Above electric loads all turned off.
PNP Signal (P/N or D range)
Whether the transmission range sensor is in P/N range or other ranges is displayed.
If it is in P or N range, “P/N” is displayed and if it is in other than P or N ranges, “D” is displayed.
Clutch SW (Declutch / Clutched)
Declutch: Clutch pedal is fully depressed.
Clutched: Clutch pedal is released.
Cruise RES/ACC Switch (“RES / +” switch, OFF/ON)
ON: “RES / +” switch is pushed.
OFF: “RES / +” switch is released.
Cruise SET/COAST Switch (“SET / –” switch, OFF/ON)
ON: “SET / –” switch is pushed.
OFF: “SET / –” switch is released.
Cruise CANCEL Switch (“CANCEL” switch, OFF/ON)
ON: “CANCEL” switch is pushed.
OFF: “CANCEL” switch is released.
Cruise ON/OFF Switch (Released / Pushed)
Pushed: “Cruise” switch is pushed.
Released: “Cruise” switch is released.
Distance Setting Switch (OFF/ON)
ON: Distance switch is pushed.
OFF: Distance switch is released.
Fuel Cut (ON/OFF)
ON: Fuel injection is cut (output signal to injector is stopped).
OFF: Fuel injection is not cut.
Closed Throttle Pos (Closed throttle position, ON/OFF)
This parameter is ON when throttle valve is fully closed and OFF when the valve is not fully closed.
O2S B1 S1 ACT (HO2S-1, Active / Inactive)
This parameter indicates the activation condition of HO2S-1.
Active: The sensor is activated.
Inactive: The sensor is being warmed up or not activated.
O2S B1 S2 ACT (HO2S-2, Active / Inactive)
This parameter indicates the activation condition of HO2S-2.
ACTIVE: The sensor is activated.
INACTIVE: The sensor is being warmed up or not activated.
Intake Valve Actuator (IMT valve actuator, Open / Closed)
This parameter indicates the state of IMT valve actuator.
ENG A-STOP (Mon, Engine running / Stopping)
This parameter indicates the state of the engine auto-stop.
ENG A-STOP (Com, Request / Not request)
This parameter indicates the state of the engine auto-stop request