Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1783    Rear Occupant Classification Sensor RH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The rear occupant classification sensor RH circuit consists of the occupant classification ECU and the rear occupant classification sensor RH.
DTC B1783 is recorded when a malfunction is detected in the rear occupant classification sensor RH circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1783
  1. The occupant classification ECU receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the rear occupant classification sensor RH circuit for 2 seconds.
  2. Rear occupant classification sensor RH malfunction
  3. Occupant classification ECU malfunction
  1. Front seat assembly RH (Rear occupant classification sensor RH)
  2. Occupant classification ECU
  3. Seat wire No. 1

WIRING DIAGRAM


H043062E54


INSPECTION PROCEDURE

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front passenger seat installation bolts to see the under surface of the seat cushion.
  2. In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause a problem, such as seat rail deformation. Hold the seat only as necessary.

1.CHECK DTC
  1. Turn the ignition switch to the ON position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Check the DTCs (Click here).

    OK:
    DTC B1783 is not output.

    HINT:
    Codes other than DTC B1783 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Check that the connectors are properly connected to the occupant classification ECU and the rear occupant classification sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3.CHECK SEAT WIRE NO. 1 (SHORT TO B+)


    C140732E04
  1. Disconnect the connectors from the occupant classification ECU and the rear occupant classification sensor RH.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester connection
    Condition
    Specified condition
    O4-4 (SGD4) - Body ground
    Ignition switch ON
    Below 1 V
    O4-6 (SVC4) - Body ground
    Ignition switch ON
    Below 1 V
    O4-10 (SIG4) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE SEAT WIRE NO. 1
OK


4.CHECK SEAT WIRE NO. 1 (OPEN)


    C111709E24
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Using a service wire, connect O8-1 (SVC4) and O8-3 (SGD4), and connect O8-2 (SIG4) and O8-3 (SGD4) of connector "C".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    O4-6 (SVC4) - O4-4 (SGD4)
    Always
    Below 1 Ω
    O4-10 (SIG4) - O4-4 (SGD4)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE SEAT WIRE NO. 1
OK


5.CHECK SEAT WIRE NO. 1 (SHORT)


    C140732E04
  1. Disconnect the service wire from connector "C".

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    O4-6 (SVC4) - O4-4 (SGD4)
    Always
    1 MΩ or higher
    O4-10 (SIG4) - O4-4 (SGD4)
    Always
    1 MΩ or higher
    O4-6 (SVC4) - O4-10 (SIG4)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE SEAT WIRE NO. 1
OK


6.CHECK SEAT WIRE NO. 1 (SHORT TO GROUND)


    C140732E04
  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    O4-4 (SGD4) - Body ground
    Always
    1 MΩ or higher
    O4-6 (SVC4) - Body ground
    Always
    1 MΩ or higher
    O4-10 (SIG4) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE SEAT WIRE NO. 1
OK


7.CHECK DTC
  1. Connect the connectors to the occupant classification ECU and the rear occupant classification sensor RH.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Check the DTCs (Click here).

    OK:
    DTC B1783 is not output.

    HINT:
    Codes other than DTC B1783 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


8.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


9.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform "Zero point calibration" (Click here).

    OK:
    "COMPLETED" is displayed.



NG
Go to step 12
OK


10.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform "Sensitivity check" (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 12
OK


11.CHECK DTC
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Check the DTCs (Click here).

    OK:
    DTC B1783 is not output.

    HINT:
    Codes other than DTC B1783 may be output at this time, but they are not related to this check.



OK
END
NG


12.REPLACE FRONT SEAT ASSEMBLY RH
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Replace the front seat assembly RH (Click here for manual seat, Click here for power seat).


NEXT


13.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Using the intelligent tester, perform "Zero point calibration" (Click here).

    OK:
    "COMPLETED" is displayed.


NEXT


14.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform "Sensitivity check" (Click here).

    Standard value:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END