Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1249/49    Open in Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

The skid control ECU inputs the stop light switch signal and detects the status of brake operation.
The skid control ECU has an open detection circuit.
If an open in the stop light switch input line or GND side stop light circuit is detected when the stop light switch is off, this DTC is output.

DTC No.
DTC Detection Condition
Trouble Area
C1249/49
ECU terminal IG1 voltage is 9.5 to 17.0 V, ABS is in non-operation, and an open in stop light switch circuit continues for 0.3 seconds or more.
  1. Stop light switch
  2. Stop light switch circuit
  3. Rear combination light (stop light) assembly

WIRING DIAGRAM


C132920E02


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

1.CHECK STOP LIGHT SWITCH OPERATION
  1. Check that the stop light comes on when the brake pedal is depressed, and goes off when the brake pedal is released.

    OK:
    Stop light switch function is normal.

    HINT:
    Check the stop light bulb as it may have burnt out.



NG
Go to step 4
OK


2.INSPECT SKID CONTROL ECU (STP TERMINAL)


    C121700E81
  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S28-7 (STP) - Body ground
    Stop light switch ON
    (Brake pedal depressed)
    8 to 14 V
    S28-7 (STP) - Body ground
    Stop light switch OFF
    (Brake pedal released)
    Below 1.5 V


    Result:

    Condition
    Proceed to
    OK (When troubleshooting in accordance with the DTC CHART)
    A
    OK (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
    B
    NG
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
A


3.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Check if the same DTC is detected (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


    Result:

    Condition
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID 

4.INSPECT STOP LIGHT SWITCH ASSEMBLY (POWER SOURCE TERMINAL)


    I042363E23
  1. Disconnect the stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S12-2 - Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


5.INSPECT STOP LIGHT SWITCH ASSEMBLY


    C124796E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S12-1 - S12-2
    Switch pin free
    Below 1 Ω
    S12-1 - S12-2
    Switch pin pushed in
    10 kΩ or higher



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


6.INSPECT STOP LIGHT OPERATION RELAY


    E068810
  1. Remove the stop light operation relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 4
    Below 1 Ω



NG
REPLACE STOP LIGHT OPERATION RELAY
OK


7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH)


    C121702E08
  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S28-7 (STP) - S12-1
    Below 1 Ω
    S28-7 (STP) - Body ground
    10 kΩ or higher

    HINT:
    1. When troubleshooting in accordance with the DTC CHART, check DTCs before replacing the master cylinder solenoid (Click here).
    2. When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE, be sure to follow the table before replacing the master cylinder solenoid (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID