Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1231/31    Steering Angle Sensor Circuit Malfunction

DTC    C1290/66    Steering Angle Sensor Zero Point Malfunction

for Preparation Click here


DESCRIPTION

The steering angle sensor signal is sent to the skid control ECU through the CAN communication system. When there is a malfunction in the communication system, it will be detected by the diagnosis function.

DTC No.
DTC Detection Condition
Trouble Area
C1231/31
When ECU IG1 terminal voltage is 9.5 V or more, the steering angle sensor malfunction signal is received.
  1. Steering angle sensor
  2. Steering angle sensor circuit
  3. Steering angle sensor power supply
  4. CAN communication system
C1290/66
The steering angle sensor zero point calibration position vastly differs from the recorded value.
Steering angle sensor

WIRING DIAGRAM


C132916E01


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

HINT:
  1. When U0073/94, U0100/65, U0123/62, U0124/95 or U0126/63 is output together with C1231/31and C1290/66, inspect and repair the trouble areas indicated by U0073/94, U0100/65, U0123/62, U0124/95 or U0126/63 first.
  2. When the speed sensor or the yaw rate and acceleration sensor has trouble, DTCs of the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs of the speed sensor (C0200/31, C0205/32, C0210/33, C0215/34, C1235/35, C1236/36, C1238/38, C1239/39) or yaw rate and acceleration sensor (C1232/32, C1234/34, C1243/43, C1244/44, C1245/45, C1381/97) are output together with other DTCs of the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor first, and then inspect and repair the steering angle sensor.

1.READ VALUE OF INTELLIGENT TESTER (STEERING ANGLE SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and push the intelligent tester main switch ON.

  1. Select "DATA LIST" mode on the intelligent tester.

    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    STEERING ANG
    Steering angle sensor/ Min.: -1152 deg/s, Max.: 1150.875 deg/s
    Left turn: Increase
    Right turn: Decrease
    -

  1. Check that the steering wheel turning angle value of the steering angle sensor displayed on the intelligent tester changes when turning the steering wheel.

    OK:
    Steering angle sensor value changes.


    Result:

    Condition
    Proceed to
    OK (When troubleshooting in accordance with DTC CHART)
    A
    OK (When troubleshooting in accordance with PROBLEM SYMPTOMS TABLE)
    B
    NG
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
Go to step 3
A


2.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 6 mph (10 km/h) or more for 10 seconds or more.

  1. Check if the same pending DTCs are detected (Click here).

    Result:

    Condition
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID 

3.INSPECT STEERING ANGLE SENSOR (POWER SOURCE AND GROUND TERMINAL)


    I046350E02
  1. Remove the steering wheel and the column cover lower.

  1. Disconnect the steering angle sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S11-1 (IG1) - Body ground
    Ignition switch ON
    10 to 14 V
    S11-9 (BAT) - Body ground
    Always
    10 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S11-2 (ESS) - Body ground
    Ignition switch OFF
    Below 1 Ω

    HINT:
    1. When troubleshooting in accordance with the DTC CHART, check DTCs before replacing the steering angle sensor (Click here).
    2. When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE, be sure to follow the table before replacing the steering angle sensor (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE OR GROUND CIRCUIT)
OK

REPLACE STEERING ANGLE SENSOR