Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1252/52    Brake Booster Pump Motor on Time Abnormally Long

for Preparation Click here


DESCRIPTION

The motor relay (semiconductor relay) is built in the master cylinder solenoid and drivers the pump motor based on a signal from the skid control ECU.

DTC No.
DTC Detection Condition
Trouble Area
C1252/52
Motor operates for 5 minutes or more.
  1. Hydraulic brake booster pump motor
  2. Hydraulic brake booster pump motor circuit
  3. Accumulator pressure sensor

HINT:
The pump motor continues operation for the first 3 minutes, then repeats start and stop.


WIRING DIAGRAM


C132922E02


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

HINT:
When C1253/53, C1254/54, or C1256/56 is output together with C1252/52, inspect and repair the trouble area indicated by C1253/53, C1254/54, or C1256/56 first.

1.CHECK PUMP MOTOR OPERATION
  1. Turn the ignition switch off.

  1. Depress the brake pedal more than 20 times.

  1. Turn the ignition switch to the ON position.

  1. Check how the pump motor operates.

    Result:

    Condition
    Proceed to
    Pump motor does not operate
    A
    Pump motor operates continuously, and does not stop
    B
    Pump motor operates intermittently
    C
    Pump motor operates, then stops
    D



B
REPLACE MASTER CYLINDER SOLENOID AND BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

C
Go to step 4

D
Go to step 5
A


2.CHECK CONNECTION OF PUMP MOTOR WIRE HARNESS (MT+ / MT-)
  1. Using a screwdriver, remove the 2 plugs from the hydraulic brake booster assembly (Click here).

  1. Check the tightening torque of the 2 screws which tighten the wire harness connecting the hydraulic brake booster assembly and the brake booster pump (Click here).

OK:
The harness is tightened to the specific torque.

Torque:
2.9 N*m{ 30 kgf*cm , 26 in.*lbf }



NG
RETIGHTEN SCREWS UP
OK


3.CHECK RESISTANCE OF PUMP MOTOR WIRE HARNESS (MT+ / MT-)


    F051186E01
  1. Using a screwdriver, remove the 2 screws and pull the wire harness from the hydraulic brake booster assembly (Click here).

  1. Measure the resistance between the red wire (MT+) and the black wire (MT-).

    Standard resistance:
    2 Ω



NG
REPLACE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY
OK


4.READ VALUE OF INTELLIGENT TESTER (ACCUMULATOR PRESSURE SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and push the intelligent tester main switch ON.

  1. Select "DATA LIST" mode on the intelligent tester.

    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    ACC PRESS
    Accumulator pressure sensor reading / Min.: 0 V, Max.: 5 V
    3.58 to 5 V
    If the value is constant regardless of pump operation, accumulator pressure sensor malfunction is suspected.

  1. Check the accumulator output value.

    Result:

    Condition
    Proceed to
    Output value is within the "Normal Condition" range
    A
    Output value is out of the "Normal Condition" range
    B
    Output value is constant regardless of pump operation
    C



B
REPLACE HYDRAULIC BRAKE BOOSTER

C
REPLACE MASTER CYLINDER SOLENOID AND BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY
A


5.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to the ON position.

  1. Wait for more than 5 minutes.

  1. Check if the same DTC is detected (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


    Result:

    Condition
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
REPLACE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY
A

REPLACE MASTER CYLINDER SOLENOID AND BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY