Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1258/58    Transfer 4WD Position Switch Circuit

for Preparation Click here


DESCRIPTION

Transfer condition (2WD or 4WD) is detected.

DTC No.
DTC Detection Condition
Trouble Area
C1258/58
The difference in 2WD/4WD information sent from the ECM via CAN and the 4WD control switch (EXI3 signal) continues for 5 seconds.
  1. 4WD control (4WD) switch
  2. 4WD control (4WD) switch circuit
  3. 4WD control ECU

WIRING DIAGRAM


C132923E01


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

1.INSPECT SKID CONTROL ECU (EXI3 TERMINAL)


    C121700E82
  1. Disconnect the skid control ECU connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S28-26 (EXI3) - Body ground
    4WD control (4WD)
    switch ON (Transfer 4WD position)
    Below 1.5 V
    S28-26 (EXI3) - Body ground
    4WD control (4WD)
    switch ON (Transfer 2WD position)
    8 to 14 V


    Result:

    Condition
    Proceed to
    OK (When troubleshooting in accordance with the DTC CHART.)
    A
    OK (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE.)
    B
    NG
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
Go to step 4
A


2.INSPECT ECM (4WD TERMINAL)


    I044051E04
  1. Turn the ignition switch off.

  1. Disconnect the ECM connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E6-8 (4WD) - Body ground
    4WD control (4WD)
    switch ON (Transfer 4WD position)
    Below 1.5 V
    E6-8 (4WD) - Body ground
    4WD control (4WD)
    switch ON (Transfer 2WD position)
    8 to 14 V



NG
Go to step 4
OK


3.RECONFIRM DTC
  1. Start the engine.

  1. Clear the DTC (Click here).

  1. Check if the same DTC is detected (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


    Result:

    Condition
    Proceed to
    DTC is output
    A
    DTC is not output
    B



NG
END
A

REPLACE MASTER CYLINDER SOLENOID 

4.INSPECT 4WD CONTROL SWITCH (GND TERMINAL)


    B059092E11
  1. Disconnect the 4WD control (4WD) switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    F11-4 (GND) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


5.INSPECT 4WD CONTROL SWITCH
  1. Check the select 2-4 and high-low system (Click here).



NG
REPLACE 4WD CONTROL SWITCH
OK


6.INSPECT 4WD CONTROL ECU
  1. Check the select 2-4 and high-low system (Click here).



NG
REPLACE 4WD CONTROL ECU
OK


7.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - 4WD CONTROL SWITCH)


    I045763E05
  1. Disconnect the 4WD control ECU (F9) connector and 4WD control (4WD) switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    F9-8 (2-4) - F11-5 (2-4)
    Below 1 Ω
    F9-8 (2-4) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4WD CONTROL ECU)


    I045764E03
  1. Disconnect the 4WD control ECU (F10) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S28-26 (EXI3) - F10-18 (ADD)
    Below 1 Ω
    S28-26 (EXI3) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ECM)


    I045573E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S28-26 (EXI3) - B6-8 (4WD)
    Below 1 Ω
    S28-26 (EXI3) - Body ground
    10 kΩ or higher


    Result:

    Condition
    Proceed to
    OK (When troubleshooting in accordance with the DTC CHART.)
    A
    OK (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE.)
    B
    NG
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

END