Home › ENGINE ยท 1GR-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


2. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for 2WD)

HINT:
(Click here)



3. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for 4WD)

HINT:
(Click here)



4. DRAIN ENGINE COOLANT

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.



    A070279E01
  1. Remove the service hole cover from the engine under cover.

  1. Install a vinyl hose onto the drain on the radiator side.

  1. Fix the vinyl hose with tape.



    A076320E02
  1. Loosen the 3 drain plugs on the engine and radiator, and drain the coolant.

  1. Remove the radiator cap.

  1. Drain the coolant from the reservoir tank.

  1. Tighten the 3 drain plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for the engine

  1. Remove the vinyl hose from the radiator.



5. DRAIN ENGINE OIL


    A076321
  1. Remove the engine under cover seal No. 3.

  1. Remove the oil pan drain plug and drain the engine oil.

  1. Clean the oil pan drain plug and install it with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



6. REMOVE BATTERY


7. REMOVE HOOD SUB-ASSEMBLY
  1. Disconnect the windshield washer hose.

  1. Separate the 2 hood supports.

  1. Remove the 4 bolts and hood.



8. REMOVE V-BANK COVER


    A075593E01
  1. Remove the 2 nuts, then remove the V-bank cover.



9. REMOVE NO. 2 VENTILATION HOSE


10. REMOVE AIR CLEANER ASSEMBLY


    A075594E01
  1. Disconnect the ventilation hose No. 2.



    A075595E01
  1. Disconnect the vacuum hose.

  1. Disconnect the mass air flow meter connector.

  1. Remove the 2 wire harness clamps.



    A075596E01
  1. Loosen the 2 hose clamps.

  1. Remove the 2 bolts, then remove the air cleaner.



11. REMOVE RADIATOR SUPPORT SEAL UPPER
  1. Remove the 11 clips and radiator support seal upper.



12. REMOVE RADIATOR ASSEMBLY


    A067113
  1. Remove the 4 bolts and radiator.



13. REMOVE FAN SHROUD
  1. Unfasten the hose clamp, and disconnect the 2 oil cooler hoses from the fan shroud.

  1. Remove the fan shroud.



14. LOOSEN FAN WITH FLUID COUPLING


    A076332
  1. Loosen the 4 fluid coupling bolts.



15. REMOVE FAN AND GENERATOR V BELT


    A076441E01
  1. While releasing the belt tension by turning the belt tensioner counterclockwise, remove the V-ribbed belt from the belt tensioner.



16. REMOVE FAN WITH FLUID COUPLING
  1. Remove the 4 bolts and fan with fluid coupling.



17. REMOVE FAN PULLEY


18. SEPARATE VANE PUMP ASSEMBLY


    A076444
  1. Disconnect the P/S oil pressure switch connector.

  1. Remove the 2 bolts, and separate the vane pump.

    NOTICE:
    Do not hit the pulley to other parts when separating the vane pump.

    HINT:
    The vane pump is suspended securely.



19. REMOVE GENERATOR ASSEMBLY


    A076407
  1. Disconnect the wire harness.

    1. Remove the bolt and wire harness stay.

    2. Disconnect the connector from the generator assembly.

    3. Remove the terminal cap and nut.

    4. Disconnect the wire harness from the terminal B.



    A076408
  1. Remove the 2 bolts and wire harness clamp bracket from the generator assembly.



    A076409
  1. Remove the 2 bolts and generator assembly.



20. SEPARATE COOLER COMPRESSOR


    A076416
  1. Remove the bolt and separate the suction hose sub-assembly.

  1. Disconnect the cooler compressor assembly connector.

  1. Remove the 4 bolts and separate cooler compressor assembly from the V-ribbed belt tensioner assembly.



21. DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY


A121823E01
  1. Remove the fuel pipe clamp.

  1. Pinch the tube connector, and then pull the fuel pipe out of the pipe as shown in the illustration.

    NOTICE:
    1. Remove any dirt and foreign objects from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



22. DISCONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY


A121824E01
  1. Remove the fuel pipe clamp.

  1. Pinch the tube connector, and then pull the fuel pipe out of the pipe as shown in the illustration.

    NOTICE:
    1. Remove any dirt and foreign objects from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



23. DISCONNECT HEATER WATER INLET HOSE B


24. DISCONNECT HEATER WATER OUTLET HOSE A (FROM HEATER UNIT)


25. REMOVE INTAKE AIR SURGE TANK


    A076500
  1. Disconnect the 2 water by-pass hoses.



    A075644
  1. Disconnect the fuel vapor feed hose.



    A075645
  1. Disconnect the ventilation hose.



    A075646
  1. Disconnect the 2 VSV connectors.

  1. Disconnect the throttle body with motor connector.

  1. Separate the 3 wire harness clamps and hose clamp.



    A076501
  1. Remove the 2 bolts and throttle body bracket.



    A076502
  1. Remove the bolt and oil baffle plate.

  1. Remove the 4 bolts and 2 surge tank stays.



    A075648
  1. Remove the 2 nuts.

  1. Using a socket hexagon wrench 8, remove the 4 bolts, intake air surge tank and gasket.



26. SEPARATE ENGINE WIRE
  1. Remove the front door scuff plate RH .

  1. Remove the cowl side trim board RH .

  1. Remove the glove compartment door .

  1. Disconnect each connector for the ECM, four wheel drive control ECU (4WD only) and instrument panel wire before pulling out the engine wire into the engine room.

  1. Disconnect the front differential connector.



27. SEPARATE NO. 2 ENGINE WIRE
  1. Disconnect the ground cable from the cylinder block.



28. REMOVE ENGINE ASSEMBLY


    A072941E02
  1. Install the 2 engine hangers with the 4 bolts as shown in the illustration.

    Part No.:
    Engine hanger No. 1: 12281-31070
    Engine hanger No. 2: 12282-31050
    Bolt: 91671-10825

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }

  1. Attach the engine sling device and hang the engine with the chain block.



    A076437
  1. Remove the 4 bolts and 4 nuts, and separate the engine mounting brackets from the frame brackets.

  1. Lift the engine out of the vehicle carefully.

    NOTICE:
    Make sure the engine is clear of all wiring and hoses.

  1. Place the engine onto a working bench.



29. REMOVE DRIVE PLATE & RING GEAR SUB-ASSEMBLY


    A076326E02
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A076327
  1. Remove the 8 bolts, front spacer, drive plate and rear spacer.



30. REMOVE ENGINE WIRE


31. REMOVE NO. 1 RADIATOR HOSE


32. REMOVE RADIATOR OUTLET, NO. 2 HOSE CLAMP OR CLIP


33. REMOVE HEATER WATER INLET HOSE A


34. REMOVE HEATER WATER OUTLET HOSE A (FROM HEATER UNIT)


35. REMOVE VENTILATION HOSE


36. REMOVE NO. 2 VENTILATION HOSE


37. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
  1. Remove the 6 nuts, exhaust manifold and gasket.



38. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH
  1. Remove the 6 nuts, exhaust manifold and gasket.



39. INSPECT EXHAUST MANIFOLD FOR FLATNESS


    A076808
  1. Using a precision straight edge and feeler gauge, measure the warpage of the contact surface of the cylinder head.

    Maximum warpage:
    0.7 mm (0.028 in.)

    If warpage is greater than the maximum, replace the exhaust manifold.

    HINT:
    Maximum warpage of each installation surface:
    0.3 mm (0.012 in.)



40. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH
  1. Remove the 4 bolts and engine mounting bracket with engine mounting insulator.



41. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH
  1. Remove the 3 bolts and engine mounting bracket with engine mounting insulator.



42. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY
  1. Remove the 2 bolts and 2 idler pulleys.



43. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
  1. Remove the bolt and idler pulley.



44. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A076445
  1. Remove the 5 bolts and V-ribbed belt tensioner.



45. REMOVE WATER INLET


    A076334
  1. Disconnect the 2 oil cooler hoses (with oil cooler).



    A076335
  1. Disconnect the 2 radiator hoses.



    A076336
  1. Disconnect the 5 water by-pass hoses.



    A076337
  1. Remove the 5 bolts and water inlet.

  1. Remove the O-ring from the water outlet pipe.

  1. Remove the gasket from the water pump.



46. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY
  1. Remove the 3 bolts, 2 nuts, oil filter bracket and gasket.



47. REMOVE INTAKE MANIFOLD
  1. Disconnect the 6 fuel injector connectors.



    A076533
  1. Remove the 10 bolts, intake manifold and 2 gaskets.



48. INSPECT INTAKE MANIFOLD FOR FLATNESS


    A076807E02
  1. Using a precision straight edge and feeler gauge, measure the warpage of the contact surface of the cylinder head and intake air surge tank.

    Maximum warpage:
    Intake air surge tank side:
    0.8 mm (0.031 in.)
    Cylinder head side:
    0.2 mm (0.008 in.)

    If warpage is greater than the maximum, replace the intake manifold.



49. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Remove the 2 bolts and 2 camshaft timing oil control valves.



50. REMOVE WATER BY-PASS JOINT RR
  1. Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the heater hose.



    A076534
  1. Remove the 2 bolts, 4 nuts, water by-pass joint RR and 2 gaskets.

  1. Remove the O-ring from the water outlet pipe.



51. REMOVE OIL FILLER CAP SUB-ASSEMBLY


52. REMOVE OIL FILLER CAP HOUSING
  1. Remove the 2 nuts, oil filler cap housing and gasket.



53. REMOVE IGNITION COIL ASSEMBLY


54. REMOVE SPARK PLUG


55. REMOVE OIL LEVEL GAUGE SUB-ASSEMBLY


56. REMOVE PARTIAL ENGINE ASSEMBLY