Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › 2009.08–2014.08
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A116143E88
4.378,1.153 6.206,1.325 1.828,0.172 10 5 V Constant Voltage Circuit 5.358,2.004 6.373,2.418 1.015,0.414 10 Microprocessor 1.501,1.075 2.429,1.237 0.927,0.162 10 from EFI Fuse 1.067,1.432 2.425,1.601 1.358,0.170 10 from EFI MAIN Relay 2.905,0.974 3.429,1.194 0.524,0.220 10 BATT 0.117,2.038 2.597,2.542 2.480,0.503 10 to Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have an IC) 0.117,3.024 2.639,3.374 2.522,0.350 10 to Engine Coolant Temperature Sensor, Mass Air Flow Meter, etc. 4.072,3.09 4.331,3.300 0.260,0.210 10 R 2.978,1.324 3.220,1.526 0.242,0.202 10 +B 3.131,2.255 3.370,2.430 0.239,0.174 10 VC 4.886,0.435 5.337,0.659 0.451,0.224 10 ECM

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON, and then goes off when the engine starts.


WIRING DIAGRAM

A229968E01
0.265,0.847 0.560,1.021 0.295,0.174 10 B22 0.265,1.018 2.023,1.359 1.758,0.341 10 VVT Sensor (for Intake Side of Bank 2) 2.579,0.853 2.818,1.018 0.239,0.165 10 VC 2.43,1.264 2.808,1.438 0.378,0.174 10 VVL+ 2.43,1.675 2.808,1.849 0.378,0.174 10 VVL- 2.921,0.754 3.049,0.933 0.128,0.179 10 3 2.921,1.174 3.049,1.353 0.128,0.179 10 1 2.921,1.576 3.049,1.755 0.128,0.179 10 2 2.43,4.654 2.852,4.829 0.422,0.174 10 VVR+ 2.43,5.065 2.808,5.240 0.378,0.174 10 VVR- 2.921,4.565 3.049,4.744 0.128,0.179 10 1 2.921,4.966 3.049,5.145 0.128,0.179 10 2 0.265,2.173 0.560,2.348 0.295,0.174 10 B24 0.265,2.344 2.146,2.685 1.881,0.341 10 VVT Sensor (for Exhaust Side of Bank 2) 2.486,2.179 2.818,2.344 0.332,0.165 10 VC2 2.501,2.379 2.809,2.554 0.308,0.174 10 EX+ 2.921,2.08 3.049,2.259 0.128,0.179 10 3 2.921,2.29 3.049,2.469 0.128,0.179 10 1 2.501,2.805 2.809,2.979 0.308,0.174 10 EX- 2.921,2.719 3.049,2.898 0.128,0.179 10 2 0.265,3.306 0.560,3.480 0.295,0.174 10 B31 0.265,3.476 2.063,3.817 1.798,0.341 10 Power Steering Oil Pressure Switch 2.579,3.311 2.818,3.477 0.239,0.165 10 VC 2.501,3.512 2.809,3.686 0.308,0.174 10 PSP 2.921,3.212 3.049,3.391 0.128,0.179 10 1 2.921,3.422 3.049,3.601 0.128,0.179 10 2 2.585,3.937 2.809,4.112 0.225,0.174 10 E2 2.921,3.852 3.049,4.031 0.128,0.179 10 3 0.265,4.445 0.560,4.620 0.295,0.174 10 B21 0.265,4.616 2.072,4.957 1.807,0.341 10 VVT Sensor (for Intake Side of Bank 1) 2.575,4.451 2.818,4.616 0.243,0.165 10 VC 2.921,4.352 3.049,4.531 0.128,0.179 10 3 0.265,5.569 0.560,5.743 0.295,0.174 10 B23 0.265,5.739 2.146,6.081 1.881,0.341 10 VVT Sensor (for Exhaust Side of Bank 1) 2.486,5.575 2.818,5.740 0.332,0.165 10 VC2 2.501,5.775 2.809,5.949 0.308,0.174 10 EX+ 2.921,5.476 3.049,5.655 0.128,0.179 10 3 2.921,5.685 3.049,5.864 0.128,0.179 10 1 2.501,6.2 2.809,6.375 0.308,0.174 10 EX- 2.921,6.115 3.049,6.294 0.128,0.179 10 2 5.308,0.862 5.603,1.037 0.295,0.174 10 B36 5.308,1.276 5.603,1.450 0.295,0.174 10 B36 5.308,1.683 5.603,1.857 0.295,0.174 10 B36 5.308,2.397 5.603,2.572 0.295,0.174 10 B36 5.308,2.804 5.603,2.978 0.295,0.174 10 B36 5.308,3.525 5.603,3.700 0.295,0.174 10 B37 5.308,3.938 5.603,4.113 0.295,0.174 10 B37 5.308,4.45 5.603,4.624 0.295,0.174 10 B36 5.308,4.66 5.603,4.834 0.295,0.174 10 B36 5.308,5.08 5.603,5.255 0.295,0.174 10 B36 5.308,5.788 5.603,5.962 0.295,0.174 10 B36 5.308,6.193 5.603,6.367 0.295,0.174 10 B36 5.34,0.682 5.538,0.854 0.198,0.172 10 16 5.34,1.099 5.538,1.271 0.198,0.172 10 12 5.34,1.496 5.538,1.668 0.198,0.172 10 11 5.34,2.213 5.538,2.385 0.198,0.172 10 18 5.34,2.628 5.538,2.800 0.198,0.172 10 17 5.34,3.344 5.538,3.516 0.198,0.172 10 16 5.382,3.759 5.538,3.931 0.156,0.172 10 8 5.34,4.272 5.538,4.444 0.198,0.172 10 15 5.396,4.826 5.538,4.998 0.142,0.172 10 9 5.34,5.241 5.538,5.413 0.198,0.172 10 10 5.34,5.591 5.538,5.763 0.198,0.172 10 13 5.34,6.011 5.538,6.183 0.198,0.172 10 14 5.634,0.773 6.068,0.935 0.434,0.163 10 VCV2 5.634,1.263 6.068,1.426 0.434,0.163 10 VV2+ 5.634,1.676 6.068,1.839 0.434,0.163 10 VV2- 5.634,2.391 6.068,2.554 0.434,0.163 10 EV2+ 5.634,2.804 6.068,2.967 0.434,0.163 10 EV2- 5.634,3.519 6.068,3.681 0.434,0.163 10 PSP 5.634,3.848 6.068,4.011 0.434,0.163 10 ETHW 5.634,4.373 6.068,4.536 0.434,0.163 10 VCV1 5.634,4.657 6.068,4.820 0.434,0.163 10 VV1+ 5.634,5.077 6.068,5.240 0.434,0.163 10 VV1- 5.634,5.778 6.068,5.941 0.434,0.163 10 EV1+ 5.634,6.198 6.068,6.361 0.434,0.163 10 EV1- 6.069,6.395 6.419,6.549 0.350,0.154 10 ECM

A388753E01
0.5,1.417 0.958,1.615 0.458,0.198 10 false B13 0.51,1.583 1.667,1.958 1.156,0.375 10 false Throttle Body with Motor Assembly 2.583,1.219 3.042,1.417 0.458,0.198 10 false VC 2.51,1.573 2.969,1.771 0.458,0.198 10 false VTA 2.448,1.917 2.906,2.115 0.458,0.198 10 false VTA2 2.604,2.271 3.063,2.469 0.458,0.198 10 false E2 2.896,1.104 3.031,1.292 0.135,0.188 10 false 5 2.896,1.49 3.031,1.677 0.135,0.188 10 false 6 2.885,1.854 3.021,2.042 0.135,0.188 10 false 4 2.885,2.219 3.021,2.406 0.135,0.188 10 false 3 0.552,3.219 1.01,3.417 0.458,0.198 10 false A3 0.563,3.385 1.719,3.76 1.156,0.375 10 false Accelerator Pedal Sensor Assembly 2.906,2.667 3.042,2.854 0.135,0.188 10 false 4 2.406,2.729 2.865,2.927 0.458,0.198 10 false VCPA 2.406,3.094 2.865,3.292 0.458,0.198 10 false VCP2 2.5,3.438 2.958,3.635 0.458,0.198 10 false VPA 2.438,3.844 2.896,4.042 0.458,0.198 10 false VPA2 2.5,4.188 2.958,4.385 0.458,0.198 10 false EPA 2.427,4.552 2.885,4.75 0.458,0.198 10 false EPA2 2.906,3 3.042,3.188 0.135,0.188 10 false 1 2.896,3.354 3.031,3.542 0.135,0.188 10 false 6 2.896,3.74 3.031,3.927 0.135,0.188 10 false 3 2.906,4.125 3.042,4.313 0.135,0.188 10 false 5 2.906,4.479 3.042,4.667 0.135,0.188 10 false 2 5.344,1.052 5.531,1.229 0.188,0.177 10 false 13 5.344,1.427 5.531,1.604 0.188,0.177 10 false 15 5.344,1.781 5.531,1.958 0.188,0.177 10 false 16 5.344,2.146 5.531,2.323 0.188,0.177 10 false 14 5.302,1.219 5.604,1.427 0.302,0.208 10 false B38 5.313,1.573 5.615,1.781 0.302,0.208 10 false B38 5.313,1.938 5.615,2.146 0.302,0.208 10 false B38 5.302,2.302 5.604,2.51 0.302,0.208 10 false B38 5.385,2.594 5.521,2.781 0.135,0.188 10 false 4 5.385,2.948 5.521,3.135 0.135,0.188 10 false 2 5.375,3.313 5.51,3.5 0.135,0.188 10 false 6 5.396,3.698 5.531,3.885 0.135,0.188 10 false 5 5.406,4.052 5.542,4.24 0.135,0.188 10 false 3 5.385,4.406 5.521,4.594 0.135,0.188 10 false 1 5.313,2.729 5.615,2.938 0.302,0.208 10 false F50 5.313,3.094 5.615,3.302 0.302,0.208 10 false F50 5.313,3.458 5.615,3.667 0.302,0.208 10 false F50 5.313,3.854 5.615,4.063 0.302,0.208 10 false F50 5.313,4.208 5.615,4.417 0.302,0.208 10 false F50 5.302,4.573 5.604,4.781 0.302,0.208 10 false F50 5.635,1.115 6.094,1.313 0.458,0.198 10 false VCTA 5.635,1.573 6.094,1.771 0.458,0.198 10 false VTA1 5.635,1.927 6.094,2.125 0.458,0.198 10 false VTA2 5.635,2.208 6.094,2.406 0.458,0.198 10 false ETA 5.625,2.646 6.083,2.844 0.458,0.198 10 false VCPA 5.625,3.01 6.083,3.208 0.458,0.198 10 false VCP2 5.625,3.448 6.083,3.646 0.458,0.198 10 false VPA 5.625,3.854 6.083,4.052 0.458,0.198 10 false VPA2 5.615,4.125 6.073,4.323 0.458,0.198 10 false EPA 5.625,4.479 6.083,4.677 0.458,0.198 10 false EPA2

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when the ignition switch is turned to ON.

OK:

MIL lights up.




OK

SYSTEM OK

NG

2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Check the communication between the intelligent tester and ECM.

Result
Result Proceed to
Communication is possible A
Communication is not possible B



B

3.CHECK MIL (THROTTLE BODY WITH MOTOR ASSEMBLY)

A

3.CHECK MIL (THROTTLE BODY WITH MOTOR ASSEMBLY)
a.

Disconnect the B13 throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B


d.

Reconnect the throttle body with motor assembly connector.



B

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)

A

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect the A3 accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B


d.

Reconnect the accelerator pedal sensor assembly connector.



B

5.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 1)

A

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 1)
a.

Disconnect the B21 VVT sensor (for Intake Side of Bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B


d.

Reconnect the VVT sensor (for Intake Side of Bank 1) connector.



B

6.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 1)

A

REPLACE VVT SENSOR (FOR INTAKE SIDE OF BANK 1)

6.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 1)
a.

Disconnect the B23 VVT sensor (for Exhaust Side of Bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B


d.

Reconnect the VVT sensor (for Exhaust Side of Bank 1) connector.



B

7.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 2)

A

REPLACE VVT SENSOR (FOR EXHAUST SIDE OF BANK 1)

7.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 2)
a.

Disconnect the B24 VVT sensor (for Exhaust Side of Bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B


d.

Reconnect the VVT sensor (for Exhaust Side of Bank 2) connector.



B

8.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 2)

A

REPLACE VVT SENSOR (FOR EXHAUST SIDE OF BANK 2)

8.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 2)
a.

Disconnect the B22 VVT sensor (for Intake Side of Bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B


d.

Reconnect the VVT sensor (for Intake Side of Bank 2) connector.



B

9.CHECK MIL (POWER STEERING OIL PRESSURE SWITCH)

A

REPLACE VVT SENSOR (FOR INTAKE SIDE OF BANK 2)

9.CHECK MIL (POWER STEERING OIL PRESSURE SWITCH)
a.

Disconnect the B31 power steering oil pressure switch connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B


d.

Reconnect the power steering oil pressure switch connector.



B

10.CHECK HARNESS AND CONNECTOR

A

10.CHECK HARNESS AND CONNECTOR
a.

Disconnect the B13 throttle body with motor assembly connector.


b.

Disconnect the A3 accelerator pedal sensor assembly connector.


c.

Disconnect the B21 VVT sensor (for Intake Side of Bank 1) connector.


d.

Disconnect the B23 VVT sensor (for Exhaust Side of Bank 1) connector.


e.

Disconnect the B24 VVT sensor (for Exhaust Side of Bank 2) connector.


f.

Disconnect the B22 VVT sensor (for Intake Side of Bank 2) connector.


g.

Disconnect the B31 power steering oil pressure switch connector.


h.

Disconnect the B36, B38 and F50 ECM connectors.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B38-13 (VCTA) - Body ground Always 10 kΩ or higher
F50-4 (VCPA) - Body ground Always 10 kΩ or higher
F50-2 (VCP2) - Body ground Always 10 kΩ or higher
B36-15 (VCV1) - Body ground Always 10 kΩ or higher
B36-16 (VCV2) - Body ground Always 10 kΩ or higher



j.

Reconnect the throttle body with motor assembly connector.


k.

Reconnect the accelerator pedal sensor assembly connector.


l.

Reconnect the VVT sensor connectors.


m.

Reconnect the power steering oil pressure switch connector.


n.

Reconnect the ECM connectors.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR