Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and pickup coil.

The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No. DTC Detection Condition Trouble Area
P0335 Either condition is met:
·

No crankshaft position sensor signal is sent to the ECM while cranking (1 trip detection logic).

·

No crankshaft position sensor signal is sent to the ECM at an engine speed of 600 rpm or more (1 trip detection logic).


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft position sensor plate

·

ECM


P0339 Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed is 1000 rpm or more.
(b) Starter signal is off.
(c) 3 seconds or more have elapsed since the starter signal switched from on to off.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft position sensor plate

·

ECM



A122767E04
0.195,0.643 0.425,0.808 0.230,0.165 10 NE 0.122,1.13 0.426,1.281 0.304,0.151 10 VV1 0.126,1.512 0.425,1.657 0.299,0.145 10 VV2 2.9,0.633 3.237,0.782 0.336,0.149 10 GND 2.9,1.587 3.237,1.736 0.336,0.149 10 GND 2.9,1.204 3.237,1.353 0.336,0.149 10 GND 0.918,1.915 1.839,2.057 0.921,0.141 10 20 msec./DIV. 2.697,0.047 3.261,0.203 0.563,0.156 10 5 V/DIV.

Reference: Inspection using an oscilloscope (VV1, VV2 and NE Signal Waveforms).

HINT:
·

The correct waveforms are as shown.

·

VV1+ and VV2+ are the VVT sensor signals, and NE+ is the crankshaft position sensor signal.

·

Grounding failure of the shielded wire may cause noise in the waveforms.



Item Content
Terminal VV1+ - VV1-
VV2+ - VV2-
NE+ - NE-
Equipment Setting 5 V/DIV.,
20 msec./DIV.
Condition Cranking or idling


MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor.

If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

WIRING DIAGRAM

A227123E01
6.001,0.539 6.400,0.695 0.399,0.156 10 VCV1 5.728,0.441 5.939,0.611 0.211,0.170 10 15 6.001,1.036 6.400,1.192 0.399,0.156 10 VV1+ 5.798,0.938 5.940,1.108 0.142,0.170 10 9 6.001,1.492 6.400,1.647 0.399,0.156 10 VV1- 5.728,1.394 5.939,1.563 0.211,0.170 10 10 6.001,2.542 6.400,2.698 0.399,0.156 10 EV1+ 5.728,2.444 5.939,2.614 0.211,0.170 10 13 6.001,3.005 6.400,3.161 0.399,0.156 10 EV1- 5.728,2.907 5.939,3.076 0.211,0.170 10 14 6.001,3.978 6.400,4.134 0.399,0.156 10 NE+ 5.798,3.88 5.940,4.050 0.142,0.170 10 6 6.001,4.441 6.400,4.597 0.399,0.156 10 NE- 5.798,4.343 5.940,4.512 0.142,0.170 10 5 6.001,5.786 6.400,5.942 0.399,0.156 10 EV2+ 5.728,5.688 5.939,5.857 0.211,0.170 10 18 6.001,6.255 6.400,6.411 0.399,0.156 10 EV2- 5.728,6.157 5.939,6.327 0.211,0.170 10 17 6.001,6.774 6.400,6.929 0.399,0.156 10 VCV2 5.728,6.675 5.939,6.845 0.211,0.170 10 16 6.001,7.257 6.400,7.413 0.399,0.156 10 VV2+ 5.728,7.159 5.939,7.329 0.211,0.170 10 12 6.001,7.726 6.400,7.882 0.399,0.156 10 VV2- 5.728,7.628 5.939,7.798 0.211,0.170 10 11 6.183,8.027 6.471,8.197 0.288,0.170 10 B36 6.183,8.189 6.534,8.344 0.350,0.156 10 ECM 3.589,1.176 3.710,1.353 0.121,0.177 10 3 4.647,0.938 4.768,1.115 0.121,0.177 10 1 4.647,1.408 4.768,1.584 0.121,0.177 10 2 3.787,1.267 4.089,1.423 0.302,0.156 10 VC 4.145,1.036 4.544,1.185 0.399,0.149 10 VVR+ 4.145,1.506 4.544,1.655 0.399,0.149 10 VVR- 3.589,2.693 3.710,2.870 0.121,0.177 10 3 4.647,2.455 4.768,2.632 0.121,0.177 10 1 4.647,2.924 4.768,3.101 0.121,0.177 10 2 2.966,3.877 3.087,4.054 0.121,0.177 10 1 2.966,4.346 3.087,4.523 0.121,0.177 10 2 3.787,2.784 4.089,2.940 0.302,0.156 10 VC2 4.243,2.553 4.544,2.702 0.302,0.149 10 EX+ 4.243,3.022 4.544,3.171 0.302,0.149 10 EX- 4.243,5.796 4.544,5.945 0.302,0.149 10 EX+ 4.243,6.266 4.544,6.415 0.302,0.149 10 EX- 3.589,5.943 3.710,6.120 0.121,0.177 10 3 4.647,5.705 4.768,5.882 0.121,0.177 10 1 4.647,6.175 4.768,6.351 0.121,0.177 10 2 3.787,6.034 4.089,6.190 0.302,0.156 10 VC2 3.589,7.414 3.710,7.591 0.121,0.177 10 3 4.647,7.176 4.768,7.353 0.121,0.177 10 1 4.647,7.646 4.768,7.822 0.121,0.177 10 2 3.787,7.506 4.089,7.661 0.302,0.156 10 VC 4.173,7.274 4.544,7.423 0.371,0.149 10 VVL+ 4.173,7.744 4.544,7.893 0.371,0.149 10 VVL- 2.968,1.639 3.235,1.795 0.267,0.156 10 B21 2.968,1.793 5.401,1.970 2.434,0.177 10 VVT Sensor (for Intake Side of Bank 1) 2.968,3.152 3.235,3.308 0.267,0.156 10 B23 2.968,3.306 5.526,3.483 2.559,0.177 10 VVT Sensor (for Exhaust Side of Bank 1) 1.63,4.581 1.897,4.737 0.267,0.156 10 B14 1.63,4.735 3.369,4.912 1.739,0.177 10 Crankshaft Position Sensor 2.561,6.388 2.828,6.544 0.267,0.156 10 B24 2.561,6.542 5.113,6.719 2.552,0.177 10 VVT Sensor (for Exhaust Side of Bank 2) 2.695,7.866 2.962,8.022 0.267,0.156 10 B22 2.695,8.02 5.128,8.197 2.434,0.177 10 VVT Sensor (for Intake Side of Bank 2) 3.906,4.973 4.493,5.129 0.586,0.156 10 Shielded

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.

·

Check the engine speed. The engine speed can be checked by using the intelligent tester. To check the engine speed, follow the procedure below:

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine.

3.

Turn the intelligent tester on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.


The engine speed may be indicated as zero despite the crankshaft revolving normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.


e.

Start the engine.


f.

Read the values displayed on the intelligent tester while the engine is running.

OK:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the intelligent tester.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the intelligent tester remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.





OK

NG

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
a.


OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B14-1 - B36-6 (NE+) Always Below 1 Ω
B14-2 - B36-5 (NE-) Always Below 1 Ω
B14-1 or B36-6 (NE+) - Body ground Always 10 kΩ or higher
B14-2 or B36-5 (NE-) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the crankshaft position sensor connector.



OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
A388055E01
1.708,1.573 2.469,1.771 0.76,0.198 10 false Clearance 0.417,1.823 0.74,2.031 0.323,0.208 10 false OK 2.635,1.813 2.958,2.021 0.323,0.208 10 false NG

a.

Check the crankshaft position sensor installation.

OK:

Sensor is installed correctly.




OK

5.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)

NG

5.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
a.

Check the teeth of the sensor plate.

OK:

Sensor plate teeth do not have any cracks or deformation.




OK

6.REPLACE CRANKSHAFT POSITION SENSOR

NG

6.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.



e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


g.

Read DTCs.

Result
Display (DTC Output) Proceed to
No output A
P0335 or P0339 B


HINT:

If the engine does not start, replace the ECM.



A

END

B