Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2014.08
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce hydrocarbon emissions, evaporated fuel from the fuel tank is routed through a canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the Purge VSV (Vacuum Switching Valve for Purge Control) so that the intake amount of hydrocarbon emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. DTC Detection Condition Trouble Area
P0443 Terminal voltage of ECM output circuit does not correspond with drive signals from ECM to purge VSV
(1 trip detection logic)
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM



WIRING DIAGRAM

A334799E03
4.115,1.625 4.385,1.771 0.271,0.146 10 false B15 4.385,1.615 5.104,1.927 0.719,0.313 10 false Purge VSV 3.458,1.448 4.063,1.76 0.604,0.313 10 false EFI NO.2 1.99,2.104 2.615,2.333 0.625,0.229 10 false EFI MAIN 1.333,1.448 1.625,1.688 0.292,0.24 10 false EFI 5.302,1.323 5.604,1.51 0.302,0.188 10 false B38 5.313,1.844 5.583,1.99 0.271,0.146 10 false F51 5.344,1.135 5.521,1.281 0.177,0.146 10 false 18 5.396,1.656 5.5,1.802 0.104,0.146 10 false 9 4.917,1.198 5.021,1.344 0.104,0.146 10 false 2 4.198,1.208 4.302,1.354 0.104,0.146 10 false 1 2.885,1.313 3.083,1.458 0.198,0.146 10 false 1D 2.938,1.135 3.042,1.281 0.104,0.146 10 false 4 0.75,1.323 0.948,1.469 0.198,0.146 10 false 1E 0.802,1.146 0.906,1.292 0.104,0.146 10 false 1 2.885,1.833 3.083,1.979 0.198,0.146 10 false 1D 1.479,2.292 1.677,2.438 0.198,0.146 10 false 1D 1.448,2.115 1.552,2.26 0.104,0.146 10 false 3 2.927,1.667 3.031,1.813 0.104,0.146 10 false 2 1.74,2.531 3.177,2.729 1.438,0.198 10 false NO.1 Integration Relay 0.771,2.906 1.24,3.219 0.469,0.313 10 false Battery 6.125,2.635 6.469,2.948 0.344,0.313 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A226931E01
0.201,1.775 0.752,1.966 0.551,0.191 10 VCV ON 0.182,0.267 0.826,0.431 0.645,0.164 10 VCV OFF

Connect the GTS to the DLC3.


b.

Disconnect the vacuum hose (canister side) from the purge VSV.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EVAP Control.


f.

When the purge VSV is operated using the GTS, check whether the port of the purge VSV applies suction to your finger.

OK:
Tester Operation Specified Condition
VSV ON Purge VSV port applies suction to finger
VSV OFF Purge VSV port applies no suction to finger




OK

NG

2.INSPECT PURGE VSV (RESISTANCE)
2.INSPECT PURGE VSV (RESISTANCE)

OK

3.INSPECT PURGE VSV (POWER SOURCE)

NG

3.INSPECT PURGE VSV (POWER SOURCE)
a.
U180626E02
0.083,0.125 0.26,0.292 0.177,0.167 10 false *a 1.552,0.531 1.823,0.74 0.271,0.208 10 false B15

Disconnect the purge VSV connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B15-1 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Purge VSV)



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - EFI RELAY)
4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
B15-2 - B38-18 (PRG) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
B15-2 or B38-18 (PRG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - EFI RELAY)
a.

Disconnect the purge VSV connector.


b.

Remove the NO. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
B15-1 - 1D-4 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
B15-1 or 1D-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR