Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0011  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)  P0012  Camshaft Position "A" - Timing Over-Retarded (Bank 1)  P0021  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2)  P0022  Camshaft Position "A" - Timing Over-Retarded (Bank 2)  


DESCRIPTION

The VVT system includes the ECM, camshaft timing oil control valve and VVT controller. The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the camshaft timing oil control valve based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the camshaft timing oil control valve. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors and performs feedback control. This is how the target intake valve timing is verified by the ECM.

A192077E13
4.483,0.815 5.318,1.026 0.834,0.211 10 VVT Sensor 4.483,1.325 6.234,1.485 1.751,0.161 10 Crankshaft Position Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 3.765,3.922 2.166,0.174 10 Camshaft Timing Oil Control Valve 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty-cycle 4.483,1.827 5.818,1.981 1.334,0.154 10 Mass Air Flow Meter 4.483,2.854 6.799,3.042 2.316,0.188 10 Engine Coolant Temperature Sensor 4.483,2.344 6.049,2.511 1.566,0.167 10 Throttle Position Sensor 4.483,3.353 5.929,3.506 1.446,0.154 10 Vehicle Speed Sensor 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 4.885,4.400 1.225,0.184 10 Camshaft Actuator 3.883,4.917 4.984,5.101 1.100,0.184 10 Intake Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC No. DTC Detection Condition Trouble Area
P0011
P0021
Valve timing cannot be adjusted when in the advance range (1 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve for intake camshaft

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


P0012
P0022
Valve timing cannot be adjusted when in the retard range (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve for intake camshaft

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM



WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

DTC P0011, P0012, P0021 or P0022 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.


HINT:
Abnormal bank Timing Over-advanced
(Valve Timing is Out of Specified Range)
Timing Over-retarded
(Valve Timing is Out of Specified Range)
Bank 1 P0011 P0012
Bank 2 P0021 P0022

·

If DTC P0011 or P0012 is output, check the right bank VVT system for intake camshaft circuit (bank 1).

·

Bank 1 refers to the bank that includes cylinder No. 1.

·

If DTC P0021 or P0022 is output, check the left bank VVT system for intake camshaft circuit (bank 2).

·

Bank 2 refers to the bank that does not include cylinder No. 1.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


d.

Read DTCs.

Result
Display (DTC Output) Proceed to
P0011, P0012, P0021 or P0022 A
P0011, P0012, P0021 or P0022 and other DTCs B

HINT:

If any DTCs other than P0011, P0012, P0021 or P0022 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the intelligent tester on.


c.

Warm up the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).


e.

Check the engine speed while operating the camshaft timing oil control valve using the intelligent tester.

OK:
Tester Operation Specified Condition
Camshaft timing oil control valve OFF Normal engine speed
Camshaft timing oil control valve ON Engine idles roughly or stalls soon after camshaft timing oil control valve switched from OFF to ON




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HASJUMPED TOOTH)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.



d.

Start the engine and warm it up.


e.

Switch the ECM from normal mode to check mode using the intelligent tester.


f.

Drive the vehicle for more than 10 minutes.


g.

Read DTCs using the intelligent tester.

OK:

No DTC output.




OK

END

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HASJUMPED TOOTH)
4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HASJUMPED TOOTH)
a.

Remove the cylinder head cover RH and LH.

A387902E02
1.5,1.26 1.875,0.854 1.875,0.854 1.5,1.479 true 2.281,1.302 1.979,1.823 1.979,1.823 2.271,1.563 true 4.615,1.396 5.031,0.99 5.031,0.99 4.615,1.656 true 5.365,1.406 5.073,2.104 5.073,2.104 5.344,1.573 true 5.083,2.094 5.396,1.583 true 1.865,0.688 2.177,0.885 0.313,0.198 10 false *1 1.885,1.844 2.198,2.042 0.313,0.198 10 false *1 5,0.823 5.313,1.021 0.313,0.198 10 false *1 4.875,2.031 5.188,2.229 0.313,0.198 10 false *1

Text in Illustration
*1 Timing Mark


b.

Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.


c.

Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.

If not, turn the crankshaft 1 revolution (360°), and then align the marks as above.


OK:

Timing marks on camshaft timing gears are aligned as shown in the illustration.



d.

Reinstall the cylinder head cover RH and LH.



OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

6.INSPECT OIL CONTROL VALVE FILTER AND PIPE

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

6.INSPECT OIL CONTROL VALVE FILTER AND PIPE
A225778E01
0.048,0 0.246,0.177 0.198,0.177 10 *1 0.048,2.293 0.246,2.469 0.198,0.177 10 *2

a.

Remove the oil pipe No. 1 or No. 2.

Text in Illustration
*1 No. 1 Oil Pipe
*2 No. 2 Oil Pipe


b.

Remove the OCV filter.


c.

Check that the filter and pipe are not clogged.

OK:

The filter and pipe are not clogged.



d.

Reinstall the OCV filter.


e.

Reinstall the oil pipe No. 1 or No. 2.



OK

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NG

REPLACE OIL CONTROL VALVE FILTER AND PIPE

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
a.

Replace the camshaft timing gear assembly (See page Engine / Hybrid System>1GR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL).



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS
8.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.



d.

Start the engine and warm it up.


e.

Switch the ECM from normal mode to check mode using the intelligent tester.


f.

Drive the vehicle for more than 10 minutes.


g.

Read output DTCs using the intelligent tester.

OK:

No DTC output.


HINT:

DTC P0011, P0012, P0021 or P0022 is stored when foreign objects in the engine oil are caught in some parts of the system. These codes will remain stored even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.




OK

SYSTEM OK

NG