Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › CAMSHAFT › 2009.08–2013.08
RM1440E _51 Engine / Hybrid System _056125 1GR-FE ENGINE MECHANICAL _0273879 CAMSHAFT A

1GR-FE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 51405A 3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 28800A 7.DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

Hide 28800 9.REMOVE BATTERY

Hide 74431 10.REMOVE BATTERY TRAY

Hide 16571C 14.REMOVE NO. 1 RADIATOR HOSE

Hide 16572D 15.REMOVE NO. 2 RADIATOR HOSE

Hide 16470 16.REMOVE RADIATOR RESERVOIR

Hide 32907C 17.DISCONNECT OIL COOLER TUBE

Hide 44310 21.DISCONNECT VANE PUMP ASSEMBLY

Hide 16604 22.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 82715 23.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 17168 24.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 11452 26.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 16206 27.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 11181A 30.REMOVE REAR CYLINDER HEAD COVER

Hide 31.DISCONNECT FUEL PIPE SUB-ASSEMBLY

Hide 11202 32.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11201 33.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11324 34.REMOVE TIMING CHAIN COVER PLATE

a.
A224737

Remove the 4 bolts, timing chain cover plate and gasket.


Hide 35.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A072945

Turn the crankshaft pulley and align the notch with the "0" timing mark of the timing chain cover.


b.
A224754E04
0.302,1.865 0.427,1.865 0.427,1.865 0.958,1.51 true 3.052,3.948 2.823,3.948 2.823,3.948 2.271,3.719 true 0.073,0.063 0.313,0.26 0.24,0.198 10 false *A 0.073,2.469 0.313,2.667 0.24,0.198 10 false *B 0.115,1.792 0.281,1.99 0.167,0.198 10 false *1 3.083,3.854 3.292,4.052 0.208,0.198 10 false *1

Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.

Text in Illustration
*A for Bank 2
*B for Bank 1
*1 Paint Mark

HINT:

If the marks are not aligned, turn the crankshaft again to align the marks.



c.

Place paint marks on the timing marks and sprockets of each camshaft timing gear and on the links of the No. 1 chain.

HINT:

Be sure to place the paint marks on 2 links of the chain and on the sprockets of the camshaft timing gears at the locations of the timing marks of the camshaft timing gears.



Hide 13540 36.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A226510E11
2.76,0.208 3.01,0.458 0.25,0.25 10 true 30° 3.115,0.896 3.302,1.063 0.188,0.167 10 false 0°

Turn the crankshaft approximately 30° counterclockwise so that there is some slack in the chain.

HINT:

This prevents the valves and pistons from interfering with each other.



b.
A226547E14
1.49,0.385 1.333,0.385 1.333,0.385 1.052,1.052 true 0.406,1.813 0.604,1.813 0.604,1.813 1,1.177 true 1.531,0.313 1.719,0.479 0.188,0.167 10 false *1 0.229,1.729 0.417,1.927 0.188,0.198 10 false *2

Align the hole in the lever of the tensioner with the hole in the tensioner body as shown in the illustration, and then insert a pin with a diameter of 1.27 mm (0.0500 in.) into the hole.

Text in Illustration
*1 Lever Hole
*2 Tensioner Hole


c.
A072945

Turn the crankshaft clockwise and align the notch with the "0" timing mark of the timing chain cover.


d.
A224739

Remove the 2 bolts and chain tensioner.

NOTICE:

Do not drop the No. 1 chain tensioner assembly or bolts into the timing chain cover.



Hide 13506 37.DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 1)

a.
A226507E11
2.771,1.24 3.021,1.417 0.25,0.177 10 true 30°

Turn the crankshaft clockwise until it is in the position shown in the illustration so that there is some slack in the chain between the banks.

HINT:

When turning the crankshaft, engine oil may spray out of the oil holes.


CAUTION:

As the camshafts turn suddenly, do not touch the camshafts or camshaft timing gears.



b.
U149629E05
1.083,1.781 1.406,1.781 1.406,1.781 1.552,2.031 true 0.51,1.698 1.073,1.875 0.563,0.177 10 true 5° to 10°

Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain can be removed easily.

HINT:

When turning the crankshaft, engine oil may spray out of the oil holes.



c.
A224759

Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.

CAUTION:

As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.



Hide 38.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

a.
A388746E01
0.552,0.542 0.74,0.542 0.74,0.542 1.177,1.021 true 1.677,1.396 1.865,1.396 1.865,1.396 1.865,1.281 true 1.542,1.292 2.052,1.292 true 0.344,0.448 0.656,0.646 0.313,0.198 10 false *1 2.094,1.198 2.323,1.406 0.229,0.208 10 true *2 0.615,4.094 0.927,4.292 0.313,0.198 10 false *a 0.615,4.365 0.927,4.563 0.313,0.198 10 false *b 0.281,2.667 0.594,2.865 0.313,0.198 10 false 10 1.177,2.135 1.49,2.333 0.313,0.198 10 false 21 2.177,2.177 2.49,2.375 0.313,0.198 10 false 15 2.906,2.208 3.219,2.406 0.313,0.198 10 false 4 0.385,2.24 0.698,2.438 0.313,0.198 10 false 9 0.271,2.906 0.458,3.073 0.188,0.167 10 false 11 0.958,2.823 1.146,2.99 0.188,0.167 10 false 23 0.948,2.583 1.135,2.75 0.188,0.167 10 false 22 0.323,3.313 0.51,3.479 0.188,0.167 10 false 7 0.125,3.75 0.313,3.917 0.188,0.167 10 false 12 0.427,3.75 0.615,3.917 0.188,0.167 10 false 8 0.958,3.375 1.146,3.542 0.188,0.167 10 false 19 1.052,3.823 1.24,3.99 0.188,0.167 10 false 24 1.302,3.823 1.49,3.99 0.188,0.167 10 false 20 2.031,3.844 2.219,4.01 0.188,0.167 10 false 14 2.042,4.094 2.229,4.26 0.188,0.167 10 false 18 2.833,3.813 3.01,3.99 0.177,0.177 10 false 2 2.844,4.052 3.031,4.219 0.188,0.167 10 false 3 2.333,3.385 2.521,3.552 0.188,0.167 10 false 13 2.344,2.865 2.531,3.031 0.188,0.167 10 false 17 2.344,2.615 2.531,2.781 0.188,0.167 10 false 16 2.979,2.677 3.167,2.844 0.188,0.167 10 false 5 3.229,2.667 3.417,2.833 0.188,0.167 10 false 6 3,3.219 3.188,3.385 0.188,0.167 10 false 1

Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install replacement bolts and washers in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 Bolt
*2 Washer
*a Part Removal
*b Replacement Bolts and Washers Installation

HINT:

Arrange the removed parts so that they can be reinstalled in their original locations.


NOTICE:
·

Do not install the bearing caps when installing replacement bolts and washers.

·

Be sure to follow the numerical order when performing this procedure.

·

Do not allow replacement bolts and washers to contact the camshaft.

·

Do not drop replacement bolts and washers into the cylinder head.




Hide 13512 39.REMOVE NO. 2 CAMSHAFT

a.
A224761

Remove the bolt of the No. 2 chain tensioner assembly.


b.
A224769

Remove the No. 2 chain tensioner assembly while lifting up the No. 2 camshaft.


c.
A224763

While lifting up the No. 2 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.


Hide 13511 40.REMOVE CAMSHAFT

a.

Lift up the rear of the camshaft so that it is at an angle.


b.
A224767

Remove the chain from the camshaft timing gear and pull out the camshaft and No. 2 chain towards the rear of the vehicle to remove them.

NOTICE:

Do not drop the chain into the gap between the engine and cover.



c.
A224765

Suspend the chain with a string or equivalent.


Hide 13506 41.DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 2)

a.
A072945

Turn the crankshaft counterclockwise and align the notch with the "0" timing mark of the timing chain cover.


b.
A224760

Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.

CAUTION:

As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.



Hide 42.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

a.
A388747E02
2.24,1.073 2.781,1.073 true 1.583,1.302 1.583,1.417 1.583,1.417 1.74,1.417 true 1.354,1.281 1.896,1.281 true 0.448,4.167 0.76,4.365 0.313,0.198 10 false *a 0.448,4.438 0.76,4.635 0.313,0.198 10 false *b 0.5,3.406 0.813,3.604 0.313,0.198 10 false 1 0.854,3.938 1.167,4.135 0.313,0.198 10 false 2 0.854,4.188 1.167,4.385 0.313,0.198 10 false 3 0.792,2.208 1.104,2.406 0.313,0.198 10 false 4 0.271,2.729 0.583,2.927 0.313,0.198 10 false 6 0.51,2.729 0.729,2.906 0.219,0.177 10 false 5 3.229,3.385 3.375,3.583 0.146,0.198 10 false 7 3.177,2.708 3.375,2.896 0.198,0.188 10 false 10 3.177,2.948 3.385,3.115 0.208,0.167 10 false 11 2.938,2.26 3.25,2.458 0.313,0.198 10 false 9 3,3.885 3.177,4.031 0.177,0.146 10 false 8 2.958,4.125 3.115,4.281 0.156,0.156 10 false 12 1.25,3.49 1.563,3.688 0.313,0.198 10 false 13 1.479,3.896 1.792,4.094 0.313,0.198 10 false 14 1.479,2.271 1.792,2.469 0.313,0.198 10 false 15 1.219,2.958 1.531,3.156 0.313,0.198 10 false 17 1.219,2.719 1.531,2.917 0.313,0.198 10 false 16 2.25,3.917 2.563,4.115 0.313,0.198 10 false 20 2.25,4.167 2.563,4.365 0.313,0.198 10 false 24 2.563,3.438 2.875,3.635 0.313,0.198 10 false 19 1.49,4.135 1.802,4.333 0.313,0.198 10 false 18 2.563,2.917 2.875,3.115 0.313,0.198 10 false 23 2.552,2.698 2.865,2.896 0.313,0.198 10 false 22 2.375,2.292 2.688,2.49 0.313,0.198 10 false 21 2.833,0.979 3.146,1.177 0.313,0.198 10 false *1 1.177,1.198 1.344,1.365 0.167,0.167 10 true *2

Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install replacement bolts and washers in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 Bolt
*2 Washer
*a Part Removal
*b Replacement Bolts and Washers Installation

HINT:

Arrange the removed parts so that they can be reinstalled in their original locations.


NOTICE:
·

Do not install the bearing caps when installing replacement bolts and washers.

·

Be sure to follow the numerical order when performing this procedure.

·

Do not allow replacement bolts and washers to contact the camshaft.

·

Do not drop replacement bolts and washers into the cylinder head.




Hide 13054 43.REMOVE NO. 4 CAMSHAFT

a.
A224762

Remove the bolt of the No. 3 chain tensioner assembly.


b.
A224770

Remove the No. 3 chain tensioner assembly while lifting up the No. 4 camshaft.


c.
A224764

While lifting up the No. 4 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.


Hide 13053 44.REMOVE NO. 3 CAMSHAFT

a.

Lift up the rear of the camshaft so that it is at an angle.


b.
A224768

Remove the chain from the camshaft timing gear and pull out the No. 3 camshaft and No. 2 chain towards the rear of the vehicle to remove them.

NOTICE:

Do not drop the chain into the gap between the engine and cover.



c.
A224766

Suspend the chain with a string or equivalent.


Hide 13050 45.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.

Fix the camshaft in place.

NOTICE:

Be careful not to damage the camshaft.



b.
A227959E08
2.052,0.854 2.438,0.125 2.438,0.125 2.542,0.125 true 0.656,1.917 0.51,1.917 0.51,1.917 0.333,1.635 false 0.969,0.906 0.719,0.26 0.719,0.26 0.552,0.26 true 1.396,1.104 1.938,1.875 true 1.25,1.573 1.49,1.896 1.49,1.896 2.073,1.896 true 0.385,0.167 0.573,0.344 0.188,0.177 10 false *1 2.125,1.823 2.313,2 0.188,0.177 10 false *1 2.573,0.031 2.771,0.208 0.198,0.177 10 false *2 0.708,1.823 0.906,2.01 0.198,0.188 10 false *3

Remove the flange bolt and camshaft timing gear assembly.

Text in Illustration
*1 Do not remove
*2 Straight Pin
*3 Flange Bolt

NOTICE:
·

Do not remove the other 3 bolts.

·

If planning to reuse the camshaft timing gear, be sure to release the straight pin lock before installing the camshaft timing gear.




Hide 13070A 46.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Fix the camshaft in place.

NOTICE:

Be careful not to damage the camshaft.



b.
A227960E11
0.313,1.656 0.469,1.875 0.469,1.875 0.604,1.875 false 0.396,0.563 0.656,0.563 0.656,0.563 0.927,0.865 false 0.854,1.188 0.656,0.563 false 1.229,1.635 1.365,1.823 1.365,1.823 1.844,1.823 false 1.313,1.271 1.688,1.823 true 1.99,0.813 2.229,0.188 2.229,0.188 2.365,0.188 true 2.417,0.125 2.604,0.313 0.188,0.188 10 false *2 0.656,1.802 0.854,1.979 0.198,0.177 10 false *3 0.208,0.49 0.385,0.677 0.177,0.188 10 false *1 1.885,1.75 2.063,1.938 0.177,0.188 10 false *1

Remove the flange bolt and camshaft timing exhaust gear assembly.

Text in Illustration
*1 Do not remove
*2 Straight Pin
*3 Flange Bolt

NOTICE:
·

Be sure not to remove the other 4 bolts.

·

If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.