The secondary air injection system injects air into the exhaust port of the cylinder head using an electric air pump, starting when the engine is started cold and operating until the catalyst warms up, in order to promote combustion of unburned fuel and decrease the amount of hydrocarbons (HC) and carbon monoxide (CO) in the exhaust gas.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0412 | All conditions are met for 3 seconds or more while idling immediately after the engine is started (1 trip detection logic):
·
Secondary air injection system is not operating (the air pump and emission control valve are off). ·
Diagnostic signal from the air injection control driver has a duty cycle of 40% (this indicates an open in the emission control valve circuit). ·
Battery voltage is 8 V or higher. |
·
Open in NO. 1 emission control valve drive circuit ·
Air injection control driver ·
NO. 1 emission control valve set ·
ECM |
| All conditions are met for 3 seconds or more while idling immediately after the engine is started (1 trip detection logic):
·
Secondary air injection system is operating (the air pump and emission control valve are on). ·
Diagnostic signal from the air injection control driver has a duty cycle of 40% (this indicates a short in the emission control valve circuit). ·
Battery voltage is 8 V or higher. |
·
Short between NO. 1 emission control valve drive circuit and body ground ·
Air injection control driver ·
NO. 1 emission control valve set ·
ECM |
This DTC indicates an open or short circuit in the circuit containing the emission control valve of the secondary air injection system. The air injection control driver performs diagnosis of the air pump assembly, NO. 1 emission control valve set and itself, and sends the results of this diagnosis to the ECM as a duty signal. When the ECM receives a signal indicating a malfunction in the air pump, air switching valve or air injection control driver, it illuminates the MIL and stores a DTC.
This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.
Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
Start the engine and warm it up.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air injection check / Automatic Mode.
Start the engine after the GTS initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
Perform the following to confirm the secondary air injection system pending codes: Press ENTER (Exit).
Check for pending DTCs.
No pending DTC is output.
After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0412.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.
By using the GTS to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Inspect the NO. 1 emission control valve set (See page Engine / Hybrid System>1GR-FE EMISSION CONTROL>AIR SWITCHING VALVE(for Bank 1)>INSPECTION).
OK
NG
Disconnect the NO. 1 emission control valve set connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B53-1 (GND) - Body ground | Always | Below 1 Ω |
Reconnect the NO. 1 emission control valve set connector.
OK
NG
Disconnect the NO. 1 emission control valve set connector.
Disconnect the air injection control driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B53-5 (+B) - A49-6 (VV) | Always | Below 1 Ω |
| B53-5 (+B) or A49-6 (VV) - Body ground | Always | 10 kΩ or higher |
Reconnect the NO. 1 emission control valve set connector.
Reconnect the air injection control driver connector.
OK
NG