Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0017  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)  P0019  Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)  


DESCRIPTION

Refer to DTC P0335 (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>P0335).

DTC No. DTC Detection Condition Trouble Area
P0017 Deviations in the crankshaft position sensor and VVT sensor 1 (for exhaust camshaft) signals (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve for exhaust camshaft

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM


P0019 Deviations in the crankshaft position sensor and VVT sensor 2 (for exhaust camshaft) signals (2 trip detection logic).

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0017 AND P0019)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


d.

Read the DTCs.

Result
Display (DTC Output) Proceed to
P0017 or P0019 A
P0017 or P0019 and other DTCs B

HINT:

If any DTCs other than P0017 or P0019 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY FOR EXHAUST CAMSHAFT)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY FOR EXHAUST CAMSHAFT)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the intelligent tester on.


c.

Warm up the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).


e.

Check the engine speed while operating the camshaft timing oil control valve using the intelligent tester.

OK:
Tester Operation Specified Condition
0% (OFF) Normal engine idle speed
127% (ON) Engine idles roughly or stalls soon after camshaft timing oil control valve switched from OFF to ON




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0017 OR P0019)

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0017 OR P0019)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.



d.

Start the engine and warm it up.


e.

Switch the ECM from normal mode to check mode using the intelligent tester (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE).


f.

Drive the vehicle for more than 10 minutes.


g.

Read the DTCs using the intelligent tester.

OK:

No DTC output.




OK

END

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)
4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)
a.

Remove the cylinder head cover RH and LH.

A387902E02
1.5,1.26 1.875,0.854 1.875,0.854 1.5,1.479 true 2.281,1.302 1.979,1.823 1.979,1.823 2.271,1.563 true 4.615,1.396 5.031,0.99 5.031,0.99 4.615,1.656 true 5.365,1.406 5.073,2.104 5.073,2.104 5.344,1.573 true 5.083,2.094 5.396,1.583 true 1.865,0.688 2.177,0.885 0.313,0.198 10 false *1 1.885,1.844 2.198,2.042 0.313,0.198 10 false *1 5,0.823 5.313,1.021 0.313,0.198 10 false *1 4.875,2.031 5.188,2.229 0.313,0.198 10 false *1

Text in Illustration
*1 Timing Mark


b.

Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.


c.

Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.

If not, turn the crankshaft 1 revolution (360°), and then align the marks as above.


OK:

Timing marks on camshaft timing gears are aligned as shown in the illustration.



d.

Reinstall the cylinder head cover RH and LH.



OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)
a.

Inspect the camshaft timing oil control valve (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

6.CHECK OIL CONTROL VALVE FILTER AND PIPE

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

6.CHECK OIL CONTROL VALVE FILTER AND PIPE
A225778E01
0.048,0 0.246,0.177 0.198,0.177 10 *1 0.048,2.293 0.246,2.469 0.198,0.177 10 *2

a.

Remove the oil pipe No. 1 or No. 2.

Text in Illustration
*1 No. 1 Oil Pipe
*2 No. 2 Oil Pipe


b.

Remove the oil control valve filter.


c.

Check that the filter and pipe are not clogged.

OK:

The filter and pipe are not clogged.



d.

Reinstall the oil control valve filter.


e.

Reinstall the oil pipe No. 1 or No. 2.



OK

7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

REPLACE OIL CONTROL VALVE FILTER OR PIPE

7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
a.

Replace the camshaft timing exhaust gear assembly (See page Engine / Hybrid System>1GR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL).



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS
8.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.



d.

Start the engine and warm it up.


e.

Switch the ECM from normal mode to check mode using the intelligent tester (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE).


f.

Drive the vehicle for more than 10 minutes.


g.

Confirm that no DTC is output using the intelligent tester.

OK:

No DTC output.


HINT:

DTC P0017 or P0019 is stored when foreign objects in the engine oil are caught in some parts of the system. These codes will remain stored even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.




OK

END

NG