Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2014.08
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P144C  Open in Secondary Air Injection System Heater Control Circuit  P144D  Short in Secondary Air Injection System Heater Control Circuit  


DESCRIPTION

The ECM operates the air pump heater relay which causes the air pump heater to operate.

DTC No. DTC Detection Condition Trouble Area
P144C Open or short in the air pump heater relay (AIR PUMP HTR) circuit for 5 seconds (1 trip detection logic).
·

Open or short in air pump heater relay (AIR PUMP HTR) circuit

·

Air pump heater relay (AIR PUMP HTR)

·

ECM


P144D Open or short in the air pump heater relay (AIR PUMP HTR) circuit for 5 seconds (1 trip detection logic).
·

Open or short in air pump heater relay (AIR PUMP HTR) circuit

·

Air pump heater relay (AIR PUMP HTR)

·

ECM



MONITOR DESCRIPTION

These DTCs are designed to detect a malfunction in the air pump heater relay (AIR PUMP HTR) circuit. When the system is normal, the battery voltage is applied to terminal HAI1 of the ECM while the air pump heater relay (AIR PUMP HTR) is turned off, and the battery voltage is not applied to terminal HAI1 of the ECM while the air pump heater relay (AIR PUMP HTR) is turned on. The ECM illuminates the MIL and stores a DTC when either one of the following conditions is detected.

·

The battery voltage is not applied to terminal HAI1 while the air pump heater relay (AIR PUMP HTR) is off.

·

The battery voltage is applied to terminal HAI1 while the air pump heater relay (AIR PUMP HTR) is on.


CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait for 10 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Air Pump Heater.

8.

Activate the air pump heater for 10 seconds or more.

HINT:
·

The active test activates the air pump heater for up to 60 seconds.

·

To protect the air pump heater, do not perform this test more than 4 times in a row.



9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

10.

Read Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P144C or P144D.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT AIR PUMP HEATER RELAY (AIR PUMP HTR)
a.

Inspect the air pump heater relay (AIR PUMP HTR) (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION).



OK

2.CHECK AIR PUMP HEATER RELAY (POWER SOURCE)

NG

REPLACE AIR PUMP HEATER RELAY (AIR PUMP HTR)

2.CHECK AIR PUMP HEATER RELAY (POWER SOURCE)
a.

Remove the air pump heater relay (AIR PUMP HTR).


b.
A288678E01
0.899,0.46 1.175,0.633 0.277,0.174 10 *1 1.64,3.093 1.917,3.267 0.277,0.174 10 *2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Air pump heater relay terminal 2 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*1 Air Pump Heater Relay (AIR PUMP HTR)
*2 Engine Room Relay Block


c.

Reinstall the air pump heater relay (AIR PUMP HTR).



OK

3.CHECK HARNESS AND CONNECTOR (ECM - AIR PUMP HEATER RELAY)

NG

4.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - AIR PUMP HEATER RELAY)
3.CHECK HARNESS AND CONNECTOR (ECM - AIR PUMP HEATER RELAY)
a.

Remove the Air pump heater relay (AIR PUMP HTR).


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Air pump heater relay (AIR PUMP HTR) terminal 1 - B38-20 (HAI1) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
Air pump heater relay (AIR PUMP HTR) terminal 1 or B38-20 (HAI1) - Body ground Always 10 kΩ or higher



d.

Reinstall the Air pump heater relay (AIR PUMP HTR).


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - AIR PUMP HEATER RELAY)
a.

Remove the Air pump heater relay (AIR PUMP HTR).


b.

Disconnect the air injection control driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Air pump heater relay (AIR PUMP HTR) terminal 2 - A49-5 (+B) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
Air pump heater relay (AIR PUMP HTR) terminal 2 or A49-5 (+B) - Body ground Always 10 kΩ or higher



d.

Reinstall the Air pump heater relay (AIR PUMP HTR).


e.

Reconnect the ECM connector.



OK

5.CHECK AIR INJECTION CONTROL DRIVER (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK AIR INJECTION CONTROL DRIVER (POWER SOURCE CIRCUIT)

OK

6.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - ECM, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - ECM, BODY GROUND)

OK

7.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE)

OK

NG