Home › Engine / Hybrid System › 1GR-FE INTAKE / EXHAUST › INTAKE MANIFOLD › 2013.08–2014.08
RM1440E _51 Engine / Hybrid System _056128 1GR-FE INTAKE / EXHAUST _0273906 INTAKE MANIFOLD A

1GR-FE INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17111 1.INSTALL INTAKE MANIFOLD

a.
A221467

Set a new gasket on each cylinder head.

NOTICE:
·

Align the port holes of the gasket and cylinder head.

·

Be careful of the installation direction.




b.

Set the intake manifold on the cylinder heads.


c.
C289995

Install and uniformly tighten the 6 bolts and 4 nuts in several passes.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

Text in Illustration
V100135

Bolt
V100136

Nut

HINT:

Tighten the inner installation bolts of the intake manifold before tightening the outer bolts.



Hide 23807 2.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23802B 3.CONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY

Hide 23801P 4.CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 17129 5.INSTALL INTAKE AIR SURGE TANK

a.

Install a new gasket to the intake air surge tank.


b.
A388855E01
0.75,1.938 0.906,2.135 0.156,0.198 10 false 1 1.75,1.938 1.906,2.135 0.156,0.198 10 false 2 0.958,0.948 1.115,1.146 0.156,0.198 10 false 3 1.458,0.938 1.615,1.135 0.156,0.198 10 false 4 0.167,1.302 0.323,1.5 0.156,0.198 10 false 5 2.563,1.531 2.719,1.729 0.156,0.198 10 false 6

Install the intake air surge tank with the 4 bolts and 2 nuts in the order shown in the illustration.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Text in Illustration
V100135

Bolt
V100136

Nut


c.

Install the No. 1 surge tank stay with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Attach the wire harness clamp.


e.

Install the No. 2 surge tank stay with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


f.

Install the throttle body bracket with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


g.
A225183E02
1.25,2.354 1.26,2.688 1.26,2.688 1.302,2.354 true 2.26,2.313 2.667,2.479 0.406,0.167 10 false 120° 2.021,0.729 2.344,0.885 0.323,0.156 10 false 45° 2.479,0.219 2.656,0.365 0.177,0.146 10 false *a 1.208,2.698 1.385,2.865 0.177,0.167 10 false *b 1.948,2.771 2.125,2.938 0.177,0.167 10 false *a 2.76,2.167 2.938,2.333 0.177,0.167 10 false *c

Connect the No. 1 ventilation hose.

Text in Illustration
*a Front
*b Matchmark
*c Top


h.

Connect the No. 1 vacuum switching valve connector.


i.

Connect the No.1 fuel feed hose.

HINT:

Connect the hose so that the direction of the hose clamp is as indicated in the illustration.



j.
A225184E02
0.979,1.354 0.99,1.698 0.99,1.698 1.031,1.354 true 0.927,1.719 1.104,1.885 0.177,0.167 10 false *b 2.01,1.625 2.188,1.792 0.177,0.167 10 false *a 1.667,1.292 1.844,1.458 0.177,0.167 10 false *c

Connect the throttle body connector.

Text in Illustration
*a Front
*b Matchmark
*c RH


k.

Connect the No. 4 water by-pass hose.


l.

Connect the No. 5 water by-pass hose.

HINT:

Connect the hose so that the direction of the hose clamp is as indicated in the illustration.



m.

Attach the 2 heater hose clamps.


Hide 17881 6.INSTALL NO. 1 AIR CLEANER HOSE

a.
A225179E11
0.771,3.906 0.667,4.052 false 0.667,4.052 0.49,4.052 false 0.885,3.844 0.615,3.573 true 0.615,3.573 0.51,3.573 false 2.094,0.813 1.75,0.625 false 1.75,0.625 1.552,0.625 false 1.646,3.75 2,3.896 0.354,0.146 10 false 90° 2.531,0.875 2.885,1.021 0.354,0.146 10 false 90° 2.177,0.5 2.531,0.646 0.354,0.146 10 false 60° 0.292,3.979 0.438,4.125 0.146,0.146 10 false *b 0.302,3.479 0.448,3.625 0.146,0.146 10 false *c 1.948,0.469 2.094,0.615 0.146,0.146 10 false *d 1.594,0.854 1.74,1 0.146,0.146 10 false *e 2.375,3.271 2.521,3.417 0.146,0.146 10 false *d 2.833,3.771 2.979,3.917 0.146,0.146 10 false *f 1.365,0.542 1.521,0.688 0.156,0.146 10 false *a

Install the No. 1 air cleaner hose with the 2 hose clamps.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

Text in Illustration
*a Paint Mark
*b Protrusion
*c Groove
*d Top
*e RH
*f Front


b.

Install the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Connect the vacuum hose and ventilation hose.

HINT:

The direction of the hose clamp is indicated in the illustration.



d.

Attach the wire harness clamp.


Hide 7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 11259 11.INSTALL V-BANK COVER

a.
A306027E02
3.042,0.583 2.74,0.583 true 1.083,0.594 1.021,0.594 1.021,0.594 0.938,0.802 false 3.104,0.51 3.271,0.677 0.167,0.167 10 false *1 1.115,0.5 1.281,0.667 0.167,0.167 10 false *2

Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins and press down on the V-bank cover to attach the pins.

Text in Illustration
*1 Pin
*2 V-bank Cover Hook


Hide 51405A 12.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 52129B 13.INSTALL FRONT BUMPER LOWER COVER (w/o TOYOTA Parking Assist-sensor System)

Hide 52822 14.INSTALL AIR INTAKE DUCT LH (w/ TOYOTA Parking Assist-sensor System)

Hide 52821 15.INSTALL AIR INTAKE DUCT RH (w/ TOYOTA Parking Assist-sensor System)

Hide 52129B 16.INSTALL FRONT BUMPER LOWER COVER (w/ TOYOTA Parking Assist-sensor System)

Hide 53298 17.INSTALL COOL AIR INTAKE DUCT (for 4WD with TOYOTA Parking Assist-sensor System)