Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2013.08–2014.08
RM1440E _51 Engine / Hybrid System _056125 1GR-FE ENGINE MECHANICAL _0273883 ENGINE ASSEMBLY A

1GR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 12281A 1.INSTALL ENGINE HANGER

a.
U147659E07
2.979,0.448 2.896,0.448 2.896,0.448 2.74,0.667 false 0.354,0.677 0.563,0.677 0.563,0.677 0.792,0.885 true 0.188,0.594 0.354,0.771 0.167,0.177 10 false *1 3.021,0.375 3.208,0.552 0.188,0.177 10 false *2 3.094,1.771 3.198,1.938 0.104,0.167 10 false 1 2.406,1.948 2.51,2.115 0.104,0.167 10 false 2 1.198,1.813 1.302,1.979 0.104,0.167 10 false 1 0.458,1.719 0.563,1.885 0.104,0.167 10 false 2

Install 2 engine hangers with 4 bolts as shown in the illustration.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

Text in Illustration
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger

HINT:
No. 1 Engine Hanger 12281-31110
No. 2 Engine Hanger 12282-31140
Bolt 91671-C0830



Hide 2.REMOVE ENGINE STAND

a.

Attach an engine sling device and hang the engine with a chain block.


b.

Lift the engine and remove it from the engine stand.


c.

Place the engine onto a work bench.


Hide 3.INSTALL ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine with a chain block.


b.

Slowly lower the engine into the engine compartment.


c.
A225433E03
1.854,0.417 2.021,0.604 0.167,0.188 10 false A 1.396,0.146 1.563,0.333 0.167,0.188 10 false A 3.052,0.5 3.219,0.677 0.167,0.177 10 true B 1.854,1.24 2.031,1.427 0.177,0.188 10 true B 1.417,1.208 1.583,1.396 0.167,0.188 10 true B 0.51,0.156 0.677,0.333 0.167,0.177 10 true B

Install the front engine mounting insulator LH with the 3 nuts and 2 bolts.

Torque:
for nut A : 72 N*m (734 kgf*cm, 53 ft.*lbf)
for nut B : 40 N*m (408 kgf*cm, 30 ft.*lbf)


d.

Install the front engine mounting insulator RH with the 3 nuts and 2 bolts.

Torque:
for nut A : 72 N*m (734 kgf*cm, 53 ft.*lbf)
for nut B : 40 N*m (408 kgf*cm, 30 ft.*lbf)


e.

Remove the 4 bolts and 2 engine hangers.


Hide 32101 4.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A388800E01
0.573,1.115 0.844,1.115 false 1.344,1.281 1.646,1.281 false 2.135,1.146 2.438,1.146 false 0.344,1.052 0.656,1.25 0.313,0.198 10 false *1 1.135,1.198 1.448,1.396 0.313,0.198 10 false *2 1.938,1.083 2.25,1.281 0.313,0.198 10 false *3

Install the front spacer, drive plate and rear spacer to the crankshaft.

Text in Illustration
*1 Front Spacer
*2 Drive Plate and Ring Gear Sub-assembly
*3 Rear Spacer
V100135

Automatic Transmission Side

HINT:

As the front spacer, drive plate and ring gear and rear spacer are not reversible, be sure to install it in the direction shown in the illustration.



c.

Apply adhesive to 2 or 3 threads at the end of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
A224777E07
1.688,0.271 1.865,0.448 0.177,0.177 10 true 1 1.646,1.698 1.813,1.875 0.167,0.177 10 true 2 2.375,1.01 2.521,1.208 0.146,0.198 10 true 3 0.917,0.958 1.063,1.167 0.146,0.208 10 true 4 2.198,0.5 2.323,0.698 0.125,0.198 10 true 5 1.125,1.49 1.271,1.667 0.146,0.177 10 true 6 2.156,1.51 2.292,1.656 0.135,0.146 10 true 7 1.188,0.417 1.333,0.573 0.146,0.156 10 true 8

Uniformly install and tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing.



e.

Tighten the 8 bolts an additional 90°.

NOTICE:

Tighten diametrically opposite bolts in pairs.



Hide 23801P 9.CONNECT NO. 1 AND NO. 2 FUEL PIPES

a.

Connect the No. 1 and No. 2 fuel pipes (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


b.

Install the No. 2 fuel pipe clamp to the fuel tube connector.


Hide 10.CONNECT HEATER WATER HOSE ASSEMBLY

a.
A225435E03
2.177,0.844 2.354,1.01 0.177,0.167 10 false *a 2.49,1.115 2.667,1.281 0.177,0.167 10 false *b 2.49,1.479 2.667,1.646 0.177,0.167 10 false *b

Connect the 2 hoses and heater water hose assembly.

Text in Illustration
*a Top
*b LH

HINT:

The direction of the hose clamp is indicated in the illustration.



Hide 82121 11.CONNECT ENGINE WIRE

a.

Connect the ECM connector.

i.
A226129E10
2.938,0.469 2.802,0.469 2.802,0.469 2.573,0.792 false 2.396,1.281 2.656,1.76 2.656,1.76 2.875,1.76 true 2.99,0.417 3.177,0.594 0.188,0.177 10 false *1 2.896,1.677 3.083,1.854 0.188,0.177 10 false *2

Attach the grommet to the wire harness support.

Text in Illustration
*1 Grommet
*2 Wire Harness Support


ii.

Pass the wire harness into the vehicle and install the wire harness support.


iii.
A227938

Connect the 6 connectors and attach the clamp.



b.

for 4WD:

i.
A222168

Attach the clamp and connect the connector.



c.
A222166

Connect the connector and install the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 55303B 12.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 11363A 13.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 82715 17.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 17105 18.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 17168 19.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17104 21.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 17167 22.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17410 24.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 88320 25.INSTALL COOLER COMPRESSOR ASSEMBLY

Hide 88704 26.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88703 27.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 16470 34.INSTALL RADIATOR RESERVOIR TANK

Hide 53294C 37.INSTALL RADIATOR SIDE DEFLECTOR LH

Hide 53293C 38.INSTALL RADIATOR SIDE DEFLECTOR RH

Hide 52521 39.INSTALL UPPER CENTER FRONT BUMPER RETAINER

Hide 40.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.

Attach the wire harness clamp.


c.

Install the air cleaner filter element sub-assembly.


Hide 52119A 42.INSTALL FRONT BUMPER COVER

Hide 74431 44.INSTALL BATTERY TRAY

Hide 28800 45.INSTALL BATTERY

Hide 28800A 47.CONNECT CABLE TO POSITIVE BATTERY TERMINAL

Hide 55781E 50.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 51.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 54.INSPECT FOR EXHAUST GAS LEAK

Hide 53292A 56.INSTALL UPPER RADIATOR SUPPORT SEAL

a.

Install the upper radiator support seal with the 13 clips.


Hide 53736B 57.INSTALL NO. 1 FRONT FENDER APRON TO FRAME SEAL RH

a.

Install the No. 1 front fender apron to frame seal with the 5 clips.


Hide 53737A 58.INSTALL NO. 1 FRONT FENDER APRON TO FRAME SEAL LH

a.

Install the No. 1 front fender apron to frame seal with the 5 clips.


Hide 53736 59.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the front fender apron seal RH with the 4 clips.


Hide 53737B 60.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal LH with the 5 clips.


Hide 51450 61.INSTALL REAR ENGINE UNDER COVER ASSEMBLY

a.

Install the rear engine under cover assembly with the 4 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51495 62.INSTALL TRANSMISSION UNDER COVER

a.

Install the transmission under cover with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51405A 63.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.
A224743

Hook the No. 1 engine under cover sub-assembly to the vehicle body as shown in the illustration.


b.

Install the 4 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 52129B 64.INSTALL FRONT BUMPER LOWER COVER (w/o TOYOTA Parking Assist-sensor System)

a.

Install the front bumper lower cover with the 5 bolts and clip.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 52822 65.INSTALL AIR INTAKE DUCT LH (w/ TOYOTA Parking Assist-sensor System)

a.

Install the air intake duct LH with the 2 screws.


b.

Install the clip and bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 52821 66.INSTALL AIR INTAKE DUCT RH (w/ TOYOTA Parking Assist-sensor System)

HINT:

Use the same procedure as for the LH side.


Hide 52129B 67.INSTALL FRONT BUMPER LOWER COVER (w/ TOYOTA Parking Assist-sensor System)

a.

Install the front bumper lower cover with the 4 bolts and clip.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 53298 68.INSTALL COOL AIR INTAKE DUCT (for 4WD with TOYOTA Parking Assist-sensor System)

Hide 53301 73.INSTALL HOOD SUB-ASSEMBLY

a.
A229695

Install the hood sub-assembly with the 8 bolts.

Torque:
for bolt A : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for bolt B : 18 N*m (178 kgf*cm, 13 ft.*lbf)

Text in Illustration
V100135

Bolt A
V100136

Bolt B


b.

Connect the washer nozzle hose.


Hide 53301 74.ADJUST HOOD SUB-ASSEMBLY