Home › Engine / Hybrid System › 1GR-FE COOLING › COOLANT › from 2013.08
RM1440E _51 Engine / Hybrid System _056129 1GR-FE COOLING _0273910 COOLANT A

1GR-FE COOLING  COOLANT  REPLACEMENT  


PROCEDURE

Hide 53298 2.REMOVE COOL AIR INTAKE DUCT (for 4WD with TOYOTA Parking Assist-sensor System)

Hide 52129B 3.REMOVE FRONT BUMPER LOWER COVER (w/o TOYOTA Parking Assist-sensor System)

Hide 52129B 4.REMOVE FRONT BUMPER LOWER COVER (w/ TOYOTA Parking Assist-sensor System)

Hide 52822 5.REMOVE AIR INTAKE DUCT LH (w/ TOYOTA Parking Assist-sensor System)

Hide 52821 6.REMOVE AIR INTAKE DUCT RH (w/ TOYOTA Parking Assist-sensor System)

Hide 51405A 7.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 51450 8.REMOVE REAR ENGINE UNDER COVER ASSEMBLY

Hide 9.DRAIN ENGINE COOLANT

CAUTION:

Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


A273797E04
1.667,0.208 1.833,0.208 1.833,0.208 2.26,0.604 false 3.167,0.188 3,0.188 3,0.188 2.635,0.844 true 2.156,2.625 2.156,3.292 true 3.958,1.563 5.719,1.563 true 1.49,0.135 1.677,0.302 0.188,0.167 10 false *1 5.781,1.49 5.969,1.656 0.188,0.167 10 false *4 2.083,3.333 2.271,3.5 0.188,0.167 10 false *3 3.219,0.125 3.406,0.292 0.188,0.167 10 false *2

Text in Illustration
*1 Reservoir Cap *2 Radiator Cap
*3 Radiator Drain Cock Plug *4 Cylinder Block Drain Cock Plug (RH side)

a.

Loosen the radiator drain cock plug.


b.

Remove the radiator cap and drain the coolant.

HINT:

Collect the coolant in a container and dispose of it according to the regulations in your area.



c.

Loosen the cylinder block drain cock plug and drain the coolant from the engine.


Hide 10.ADD ENGINE COOLANT

a.

Tighten the cylinder block drain cock plug.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


b.

Tighten the radiator drain cock plug by hand.


c.

Add engine coolant.

Standard Capacity:

10.5 liters (11.1 US qts, 9.2 Imp. qts)


NOTICE:

Do not substitute plain water for engine coolant.


HINT:
·

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

·

Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.




d.

Slowly pour coolant into the radiator reservoir until it reaches the F line.


e.

Install the reservoir cap.


f.

Install the radiator cap.*1


g.

Start the engine and stop it immediately.*2


h.

Allow approximately 10 seconds to pass. Then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3


i.

Repeat steps *1, *2 and *3 until the coolant level does not decrease.

HINT:

Be sure to perform this step while the engine is cold, as air in the No. 1 radiator hose will flow into the radiator if the engine is warmed up and the thermostat opens.



j.

Install the radiator cap.*4


k.

Set the air conditioning as follows.*5

Item Condition
Fan speed Any setting except off
Temperature Toward WARM
Air conditioning switch Off


l.

Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6

CAUTION:
·

Wear protective gloves. Hot areas on the parts may injure your hands.

·

Be careful of the fan.

·

Be careful as the engine, radiator and radiator hoses are hot and can cause burns.



NOTICE:
·

Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the F line.

·

Do not start the engine when there is no coolant in the radiator reservoir.

·

Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.

·

If there is not enough coolant, the engine may burn out or overheat.



HINT:
·

Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air while warming up the engine.

·

The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand and checking when the engine coolant starts to flow inside the hose.




m.

Stop the engine, wait until the engine coolant cools down to ambient temperature. Then remove the radiator cap and check the coolant level.*7

CAUTION:

Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



n.

If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8


o.

If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the F line.

If the coolant level is below the F line, repeat steps *4 through *8.

If the coolant level is above the F line, drain coolant until the coolant level reaches the F line.


Hide 51450 12.INSTALL REAR ENGINE UNDER COVER ASSEMBLY

Hide 51405A 13.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 52129B 14.INSTALL FRONT BUMPER LOWER COVER (w/o TOYOTA Parking Assist-sensor System)

Hide 52822 15.INSTALL AIR INTAKE DUCT LH (w/ TOYOTA Parking Assist-sensor System)

Hide 52821 16.INSTALL AIR INTAKE DUCT RH (w/ TOYOTA Parking Assist-sensor System)

Hide 52129B 17.INSTALL FRONT BUMPER LOWER COVER (w/ TOYOTA Parking Assist-sensor System)

Hide 53298 18.INSTALL COOL AIR INTAKE DUCT (for 4WD with TOYOTA Parking Assist-sensor System)