Home › Drivetrain › A750E AUTOMATIC TRANSMISSION / TRANSAXLE › OIL COOLER
RM1440E _52 Drivetrain _056133 A750E AUTOMATIC TRANSMISSION / TRANSAXLE _0273929 OIL COOLER A

A750E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL COOLER  INSTALLATION  


PROCEDURE

Hide 32907C 1.INSTALL NO. 2 OIL COOLER TUBE SUB-ASSEMBLY

a.
U148356E02
3.094,0.802 3.229,0.958 0.135,0.156 10 false A 2.469,1.844 2.594,2 0.125,0.156 10 false B

Temporarily install the oil cooler tube to the fan shroud with bolt A. Install bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 32943A 2.INSTALL NO. 2 OIL COOLER INLET HOSE AND NO. 2 OIL COOLER OUTLET HOSE

a.
U148528E02
0.583,2.094 0.406,2.646 0.406,2.646 0.323,2.646 false 0.156,2.563 0.365,2.781 0.208,0.219 10 false *1

Connect the No. 2 oil cooler inlet hose and No. 2 oil cooler outlet hose to the No. 2 oil cooler tube.

Text in Illustration
*1 Yellow Point Mark


b.

Connect the 2 hoses to the radiator to install them.

NOTICE:
·

When connecting the hoses to the tube, support the tube by hand and be careful to prevent the tube from being deformed.

·

Make sure the paint mark and pinching portion of each clip are facing the directions shown in the illustration.




Hide 32921 3.INSTALL NO. 1 INLET OIL COOLER TUBE AND NO. 1 OUTLET OIL COOLER TUBE

U150319E01
2.836,0.922 2.837,0.947 false 2.877,0.761 2.88,0.732 2.88,0.732 2.904,0.714 false 2.877,0.761 2.89,0.768 2.89,0.768 2.906,0.778 false 2.933,0.731 2.916,0.721 2.916,0.721 2.904,0.714 false 2.888,0.736 2.88,0.732 false

a.

Install the 2 No. 2 flexible hose clamps with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


b.

Temporarily install the ends of the 2 oil cooler tubes to each oil cooler tube union by hand.


c.

Close the 2 No. 2 flexible hose clamps and install the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


d.

Using a union nut wrench, tighten the inlet and outlet tubes.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 32941A 4.INSTALL NO. 1 OIL COOLER INLET HOSE AND NO. 1 OIL COOLER OUTLET HOSE

U150061E01
2.848,0.197 3.013,0.357 0.165,0.161 10 *1 2.5,0.733 2.670,0.889 0.170,0.156 10 *2 3.024,1.727 3.207,1.883 0.184,0.156 10 *3 2.741,1.571 2.781,1.608 0.04,0.037 2.747,1.564 2.913,1.817 2.913,1.817 3.022,1.817 false 2.295,1.348 2.344,1.366 0.049,0.019 2.372,0.258 2.805,0.283 false 2.805,0.283 2.39,0.447 false 2.753,0.462 2.66,0.719 false 2.66,0.719 2.888,0.593 false

a.

Connect the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose to the oil cooler inlet tube and No. 1 oil cooler outlet tube.

Text in Illustration
*1 Blue Paint Mark
*2 Pink Paint Mark
*3 White Paint Mark


b.

Connect the 2 hoses to the No. 2 oil cooler tube to install them, and then pass the 2 hoses through the No. 1 flexible hose clamp and close the clamp.

NOTICE:
·

When connecting the hoses to the tube, support the tube by hand and be careful to prevent the tube from being deformed.

·

Make sure the paint marks and pinching portion of each clip are facing the directions shown in the illustration.




Hide 5.ADJUST AUTOMATIC TRANSMISSION FLUID LEVEL

a.

Hide 53736B 6.INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL RH

Hide 51450 8.INSTALL REAR ENGINE UNDER COVER ASSEMBLY

Hide 51405A 9.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY