Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2009.08–2013.08
RM1440E _51 Engine / Hybrid System _056125 1GR-FE ENGINE MECHANICAL _0273883 ENGINE ASSEMBLY A

1GR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 12281A 1.INSTALL ENGINE HANGER

a.
U147659E07
2.979,0.448 2.896,0.448 2.896,0.448 2.74,0.667 false 0.354,0.677 0.563,0.677 0.563,0.677 0.792,0.885 true 0.188,0.594 0.354,0.771 0.167,0.177 10 false *1 3.021,0.375 3.208,0.552 0.188,0.177 10 false *2 3.094,1.771 3.198,1.938 0.104,0.167 10 false 1 2.406,1.948 2.51,2.115 0.104,0.167 10 false 2 1.198,1.813 1.302,1.979 0.104,0.167 10 false 1 0.458,1.719 0.563,1.885 0.104,0.167 10 false 2

Install 2 engine hangers with 4 bolts as shown in the illustration.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

Text in Illustration
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger

HINT:
No. 1 Engine Hanger 12281-31110
No. 2 Engine Hanger 12282-31140
Bolt 91671-C0830



Hide 2.REMOVE ENGINE STAND

a.

Attach an engine sling device and hang the engine with a chain block.


b.

Lift the engine and remove it from the engine stand.


c.

Place the engine onto a work bench.


Hide 3.INSTALL ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine with a chain block.


b.

Slowly lower the engine into the engine compartment.


c.
A225433E03
1.854,0.417 2.021,0.604 0.167,0.188 10 false A 1.396,0.146 1.563,0.333 0.167,0.188 10 false A 3.052,0.5 3.219,0.677 0.167,0.177 10 true B 1.854,1.24 2.031,1.427 0.177,0.188 10 true B 1.417,1.208 1.583,1.396 0.167,0.188 10 true B 0.51,0.156 0.677,0.333 0.167,0.177 10 true B

Install the front engine mounting insulator LH with the 3 nuts.

Torque:
for nut A : 72 N*m (734 kgf*cm, 53 ft.*lbf)
for nut B : 40 N*m (408 kgf*cm, 30 ft.*lbf)


d.

Install the front engine mounting insulator RH with the 3 nuts.

Torque:
for nut A : 72 N*m (734 kgf*cm, 53 ft.*lbf)
for nut B : 40 N*m (408 kgf*cm, 30 ft.*lbf)


e.

Remove the 4 bolts and 2 engine hangers.


Hide 32101 4.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A388800E01
0.573,1.115 0.844,1.115 false 1.344,1.281 1.646,1.281 false 2.135,1.146 2.438,1.146 false 0.344,1.052 0.656,1.25 0.313,0.198 10 false *1 1.135,1.198 1.448,1.396 0.313,0.198 10 false *2 1.938,1.083 2.25,1.281 0.313,0.198 10 false *3

Install the front spacer, drive plate and rear spacer to the crankshaft.

Text in Illustration
*1 Front Spacer
*2 Drive Plate and Ring Gear
*3 Rear Spacer
V100135

Automatic Transmission Side

HINT:

As the front spacer, drive plate and ring gear and rear spacer are not reversible, be sure to install it in the direction shown in the illustration.



c.

Apply adhesive to 2 or 3 threads at the end of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
A224777E07
1.688,0.271 1.865,0.448 0.177,0.177 10 true 1 1.646,1.698 1.813,1.875 0.167,0.177 10 true 2 2.375,1.01 2.521,1.208 0.146,0.198 10 true 3 0.917,0.958 1.063,1.167 0.146,0.208 10 true 4 2.198,0.5 2.323,0.698 0.125,0.198 10 true 5 1.125,1.49 1.271,1.667 0.146,0.177 10 true 6 2.156,1.51 2.292,1.656 0.135,0.146 10 true 7 1.188,0.417 1.333,0.573 0.146,0.156 10 true 8

Uniformly install and tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
83 N*m (846 kgf*cm, 61 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing.



Hide 5.CONNECT OIL COOLER TUBE SUB-ASSEMBLY (for Automatic Transmission)

a.

Connect the oil cooler tube with the bolt.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 88704 6.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Connect the suction hose with the bolt.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


Hide 12371 7.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR (for 4WD)

Hide 12371 8.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR (for 2WD)

Hide 35000 9.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

a.

for 4WD:

Install the automatic transmission to the vehicle (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION ASSEMBLY>INSTALLATION).


b.

for 2WD:

Install the automatic transmission to the vehicle (See page Drivetrain>A750E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION ASSEMBLY>INSTALLATION).


Hide 23801P 13.CONNECT NO. 1 AND NO. 2 FUEL PIPES

a.

Connect the No. 1 and No. 2 fuel pipes (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


b.

Install the No. 2 fuel pipe clamp to the fuel tube connector.


Hide 14.CONNECT HEATER WATER HOSE ASSEMBLY

a.
A225435E03
2.177,0.844 2.354,1.01 0.177,0.167 10 false *a 2.49,1.115 2.667,1.281 0.177,0.167 10 false *b 2.49,1.479 2.667,1.646 0.177,0.167 10 false *b

Connect the 2 hoses and heater water hose.

HINT:

The direction of the hose clamp is indicated in the illustration.


Text in Illustration
*a Top
*b LH


Hide 82121 15.CONNECT ENGINE WIRE

a.

Connect the ECM connector.

i.
A226129E10
2.938,0.469 2.802,0.469 2.802,0.469 2.573,0.792 false 2.396,1.281 2.656,1.76 2.656,1.76 2.875,1.76 true 2.99,0.417 3.177,0.594 0.188,0.177 10 false *1 2.896,1.677 3.083,1.854 0.188,0.177 10 false *2

Attach the grommet to the wire harness support.

Text in Illustration
*1 Grommet
*2 Wire Harness Support


ii.

Pass the wire harness into the vehicle and install the wire harness support.


iii.
A227938

Connect the 6 connectors and attach the clamp.




c.
A222168

for 4WD:

Attach the clamp and connect the connector.


d.
A222166

Connect the connector and install the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 11363A 16.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 82715 20.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 17105 21.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 17168 22.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17104 24.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 17167 25.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17410 27.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Hide 88320 28.INSTALL COOLER COMPRESSOR ASSEMBLY

Hide 88704 29.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88703 30.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 16572D 38.INSTALL NO. 2 RADIATOR HOSE

Hide 16571C 39.INSTALL NO. 1 RADIATOR HOSE

Hide 53294C 40.INSTALL RADIATOR SIDE DEFLECTOR LH

Hide 53293C 41.INSTALL RADIATOR SIDE DEFLECTOR RH

Hide 52521 42.INSTALL UPPER FRONT BUMPER RETAINER

Hide 43.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.

Attach the wire harness clamp.


c.

Install the air cleaner filter element.


Hide 52119A 45.INSTALL FRONT BUMPER COVER

a.

Install the front bumper cover (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>INSTALLATION).


Hide 74431 47.INSTALL BATTERY TRAY

Hide 28800 48.INSTALL BATTERY

Hide 28800A 50.CONNECT CABLE TO POSITIVE BATTERY TERMINAL

Hide 55781E 53.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Install the cowl top ventilator louver (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).


Hide 54.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 57.INSPECT FOR EXHAUST GAS LEAK

Hide 53292A 59.INSTALL UPPER RADIATOR SUPPORT SEAL

a.

Install the upper radiator support seal with the 13 clips.


Hide 53736B 60.INSTALL NO. 1 FRONT FENDER APRON TO FRAME SEAL RH

a.

Install the No. 1 front fender apron to frame seal with the 5 clips.


Hide 53737A 61.INSTALL NO. 1 FRONT FENDER APRON TO FRAME SEAL LH

a.

Install the No. 1 front fender apron to frame seal with the 5 clips.


Hide 53736 62.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the front fender apron seal with the 5 clips.


Hide 53737B 63.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal with the 5 clips.


Hide 51450 64.INSTALL REAR ENGINE UNDER COVER ASSEMBLY

a.

Install the rear engine under cover with the 4 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51495 65.INSTALL TRANSMISSION UNDER COVER

a.

Install the transmission under cover with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51405A 66.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.
A224743

Hook the engine under cover to the vehicle body as shown in the illustration.


b.

Install the 4 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 52129B 67.INSTALL FRONT BUMPER COVER LOWER

a.

Install the front bumper cover lower with the 5 bolts and clip.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68.PERFORM RESET MEMORY

Hide 53301 72.INSTALL HOOD SUB-ASSEMBLY

a.
A229695

Install the hood with the 8 bolts.

Torque:
for bolt A : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for bolt B : 18 N*m (184 kgf*cm, 13 ft.*lbf)

Text in Illustration
V100135

Bolt A
V100136

Bolt B


b.

Connect the washer nozzle hose.


Hide 53301 73.ADJUST HOOD SUB-ASSEMBLY