Home › Drivetrain › A750E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT
RM1440E _52 Drivetrain _056133 A750E AUTOMATIC TRANSMISSION / TRANSAXLE _0273934 AUTOMATIC TRANSMISSION UNIT A

A750E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 35573 1.REMOVE TRANSMISSION CONTROL SHAFT LEVER LH

C212489

a.

Remove the nut, spring washer and control shaft lever LH.


Hide 84540 2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

D027903

a.

Using a screwdriver, bend the tabs of the lock washer.


b.

Remove the nut, lock washer and bolt.


c.

Remove the park/neutral position switch.


Hide 32921C 3.REMOVE OIL COOLER TUBE UNION

C214945

a.

Remove the 2 oil cooler tube unions.


b.

Remove the 2 O-rings from the oil cooler tube unions.


Hide 89413B 4.REMOVE SPEED SENSOR

C111258

a.

Remove the 2 bolts and 2 speed sensors.


b.

Remove the 2 O-rings from the sensors.


Hide 35122 5.REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE

C212491

a.

Remove the 2 bolts.


b.

Remove the breather tube.


c.

Remove the O-ring from the tube.


Hide 35111 6.REMOVE AUTOMATIC TRANSMISSION HOUSING

C210181

a.

Remove the 10 bolts.


b.

Remove the transmission housing.


Hide 35108 7.REMOVE EXTENSION HOUSING SUB-ASSEMBLY

D027972

a.

Remove the 6 bolts.


b.

Remove the extension housing.

HINT:

Use a brass bar and hammer to remove the extension housing.



c.
D029874

Using a snap ring expander, remove the snap ring.


d.

Remove the thrust needle roller bearing and 2 bearing races.


e.

Remove the 2 transfer case ring pins from the transmission case adapter.


Hide 8.REMOVE EXTENSION HOUSING DUST DEFLECTOR

D027976

a.

Using a brass bar and hammer, tap out the dust deflector.


Hide 35108R 9.REMOVE AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL

D027977E03
3.417,0 3.104,0 false 1.521,0.344 1.771,0.344 false 1.24,0.271 1.583,0.448 0.344,0.177 10 false SST

a.

Using SST, tap out the oil seal.

SST
09308-00010  


Hide 35104 10.FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

D027911

a.

Install the transmission case to an overhaul attachment.


Hide 35106 11.REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

NOTICE:

Do not turn the transmission over as this will contaminate the valve body with foreign matter in the bottom of the pan.


a.

Remove the drain plug and 20 bolts.


b.

Remove the 4 magnets from the oil pan.


Hide 35106 12.INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

Hide 35330 13.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

D012703

a.

Turn over the transmission.


b.

Remove the 4 bolts and oil strainer from the valve body.


c.

Remove the O-ring from the oil strainer.


Hide 82125J 14.REMOVE TRANSMISSION WIRE

D012704E06
1.156,1.01 2.49,0.188 2.49,0.188 1.135,1.448 true 2.542,0.094 2.781,0.26 0.24,0.167 10 false *1

a.

Remove the 2 bolts and 2 temperature sensor clamps, and disconnect the 2 ATF temperature sensors.

Text in Illustration
*1 Temperature Sensor Clamp


b.

Disconnect the 7 connectors from the solenoid valves.


c.
D027912

Remove the bolt from the case.


d.

Pull the transmission wire out of the transmission case to remove it.


e.

Remove the O-ring from the transmission wire.


Hide 35410 15.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.

Remove the bolt, detent spring cover and detent spring.


b.
U115774

Remove the 19 bolts and valve body.


Hide 35145C 16.REMOVE TRANSMISSION CASE GASKET

D027968

a.

Remove the 3 gaskets.


Hide 35159 17.REMOVE BRAKE DRUM GASKET

D027969

a.

Remove the 3 gaskets.


Hide 35251 18.REMOVE CHECK BALL BODY

D027914E16
1.283,0.494 0.808,0.494 false 1.555,1.219 0.653,1.219 false 0.627,0.384 0.785,0.575 0.158,0.191 10 *1 0.473,1.1 0.631,1.291 0.158,0.191 10 *2

a.

Remove the check ball body and spring.

Text in Illustration
*1 Check Ball Body
*2 Spring


Hide 35425A 19.REMOVE C-2 ACCUMULATOR PISTON

D027915

a.

Apply compressed air to the oil hole to remove the C-2 accumulator piston and spring.


b.

Remove the 2 O-rings from the piston.

NOTICE:

Be careful as the C-3 and B-3 accumulator pistons may jump out.



Hide 35427K 20.REMOVE B-3 ACCUMULATOR PISTON

D027915

a.

Apply compressed air to the oil hole to remove the B-3 accumulator piston and spring.


b.

Remove the 2 O-rings from the piston.

NOTICE:

Be careful as the C-3 accumulator piston may jump out.



Hide 35426D 21.REMOVE C-3 ACCUMULATOR PISTON

D027916

a.

Apply compressed air to the oil hole to remove the C-3 accumulator piston and 2 springs.


b.

Remove the 2 O-rings from the piston.


Hide 35424F 22.REMOVE C-1 ACCUMULATOR VALVE

D027917

a.

Remove the C-1 accumulator valve and 2 springs.


Hide 35595 23.REMOVE PARKING LOCK PAWL BRACKET

U150400E01
2.993,0 3.414,0.08 0.421,0.08

a.

Remove the 3 bolts and bracket.


Hide 35501 24.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

D012709

a.

Disconnect the parking lock rod from the manual valve lever to remove it.


Hide 35556 25.REMOVE PARKING LOCK PAWL SHAFT

D028846

a.

Pull out the parking lock pawl shaft from the front side to remove it, and then remove the lock pawl and spring.


b.

Remove the E-ring from the shaft.


Hide 35505 26.REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

D027918

a.

Using a hammer and screwdriver, cut off the spacer and remove it from the shaft.


b.
D027919

Using a pin punch and hammer, tap out the spring pin.

HINT:

Slowly drive out the spring pin so that it does not fall into the transmission case.



c.

Pull the manual valve lever shaft out through the case and remove the manual valve lever.


Hide 35506F 27.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

U116381E03
1.563,0.781 1.625,0.833 false 1.635,0.677 1.698,0.729 false 1.698,0.583 1.76,0.635 false 1.75,0.49 1.823,0.552 false 1.802,0.406 1.875,0.469 false

a.

Using a screwdriver, pry out the 2 oil seals.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the transmission case.



Hide 28.REMOVE OIL PUMP ASSEMBLY

D027921

a.

Remove the 10 bolts.


b.
D027922E04
1.854,0.906 2.063,0.448 false 2.104,0.302 2.438,0.448 0.333,0.146 10 false SST

Using SST, remove the oil pump.

SST
09350-30020  (09350-07020)


c.
D028796

Remove the O-ring from the front oil pump.


d.
C177431

Remove the 2 thrust bearing races from the front oil pump.


Hide 29.REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

D027923

a.

Remove the clutch drum and input shaft assembly from the transmission case.


b.
C177432

Remove the clutch drum thrust washer and 2 thrust needle roller bearings.


Hide 35780B 31.REMOVE NO. 2 1-WAY CLUTCH ASSEMBLY

D027994

a.

Remove the 1-way clutch and No. 2 clutch drum thrust washer from the clutch drum and input shaft assembly.


Hide 35601 32.FIX CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

D027995E04
2.427,1.729 2.656,0.99 2.656,0.99 2.75,0.99 false 1.104,1.313 0.865,0.792 0.865,0.792 0.802,0.792 false 2.771,0.885 2.948,1.083 0.177,0.198 10 false *1 0.583,0.719 0.771,0.938 0.188,0.219 10 false *2

a.

Place the oil pump onto the torque converter clutch, and then place the clutch drum and input shaft assembly onto the oil pump.

Text in Illustration
*1 Torque Converter Clutch
*2 Oil Pump


Hide 35049 33.REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY

D027996

a.

Using a screwdriver, remove the snap ring.


b.
D027997

Remove the reverse clutch hub sub-assembly, reverse clutch reaction sleeve, clutch cushion, plate reverse clutch flange, 5 reverse clutch discs and 4 clutch plates from the clutch drum.


Hide 35659 34.REMOVE REVERSE CLUTCH REACTION SLEEVE

D027998

a.

Remove the reverse clutch reaction sleeve from the reverse clutch hub.


Hide 35677C 35.REMOVE REAR CLUTCH DISC

a.

Remove the clutch cushion plate, reverse clutch flange, 5 discs and 4 plates from the reverse clutch hub.


Hide 35061 38.REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

D028001

a.

Remove the forward clutch hub from the clutch drum.


b.
D028500

Remove the 2 thrust needle roller bearings from the forward clutch hub.


Hide 35631 40.REMOVE MULTIPLE DISC CLUTCH HUB

D028502

a.

Remove the multiple disc clutch hub from the clutch drum.


b.
D028503

Remove the 2 thrust bearing races from the multiple disc clutch hub.


Hide 35701 41.REMOVE INPUT SHAFT ASSEMBLY

D028504

a.

Remove the thrust needle roller bearing from the clutch drum.


b.
D028505

Remove the input shaft assembly from the clutch drum.


Hide 35712A 42.REMOVE INPUT SHAFT OIL SEAL RING

D029677

a.

Remove the 3 oil seal rings from the input shaft.


Hide 35633B 43.REMOVE FORWARD MULTIPLE DISC CLUTCH DISC

D028519

a.

Using a screwdriver, remove the hole snap ring.


b.

Remove the 2 flanges, 6 discs and 5 plates from the input shaft.


Hide 35668 45.REMOVE NO. 1 CLUTCH BALANCER

D028521E03
2.083,0.552 2.344,0.229 false 2.375,0.083 3.063,0.448 0.688,0.365 10 false SST

a.

Place SST on the clutch balancer and compress the return spring with a press.

SST
09350-30020  (09350-07040, 09350-07070)


b.

Using a snap ring expander, remove the snap ring.


c.
D028522

Remove the clutch balancer and forward clutch return spring from the input shaft assembly.


d.
D028523

Remove the O-ring from the No. 1 clutch balancer.


Hide 35603A 46.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35612B 47.REMOVE FORWARD CLUTCH PISTON

D028524

a.

Hold the input shaft by hand and apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the input shaft to remove the forward clutch piston.


b.
D028525

Remove the 2 O-rings from the forward clutch piston.


Hide 35649 48.REMOVE REVERSE CLUTCH FLANGE

D028506

a.

Remove the reverse clutch flange from the clutch drum.


Hide 35667A 49.REMOVE DIRECT CLUTCH DISC

D028507

a.

Using a screwdriver, remove the 2 hole snap rings from the clutch drum.


b.

Remove the reverse clutch flange, 5 discs and 5 plates from the clutch drum.


Hide 35668 51.REMOVE NO. 3 CLUTCH BALANCER

D028509E05
1.708,0.885 2.479,0.573 2.479,0.573 2.26,0.927 false 2.531,0.385 2.875,0.583 0.344,0.198 10 false SST

a.

Place SST on the clutch balancer and compress the return spring with a press.

SST
09387-00070  


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


Hide 35047 52.REMOVE REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

D028510

a.

Remove the reverse clutch return spring and O-ring from the reverse clutch piston.


Hide 35047 53.INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35048 54.REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY

D028511

a.

Remove the reverse clutch piston sub-assembly from the clutch drum.


b.
D028512

Remove the O-ring from the reverse clutch piston.


c.
D028513

Remove the O-ring from the clutch drum.


Hide 35606A 55.REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

D028514E08
1.406,1.333 0.521,1.396 0.521,1.396 1.208,0.604 false 0.167,1.375 0.51,1.573 0.344,0.198 10 false SST

a.

Place SST on the direct clutch piston and compress the return spring with a press.

SST
09320-89010  


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.
D028515

Using 2 screwdrivers, remove the direct clutch piston sub-assembly from the clutch drum.


d.
D028517

Remove the No. 2 clutch balancer and direct clutch return spring from the direct clutch piston.


e.
D028816

Remove the 2 O-rings from the direct clutch piston.


Hide 35604 56.INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35679C 57.REMOVE NO. 3 BRAKE SNAP RING

D027925

a.

Using a screwdriver, remove the No. 3 brake snap ring from the case.


Hide 58.REMOVE NO. 3 BRAKE DISC

a.

Remove the flange, 4 discs, 4 plates and cushion plate from the case.


Hide 35624J 60.REMOVE 2ND BRAKE PISTON HOLE SNAP RING

D027927E23
1.406,0.292 0.698,0.292 false 0.292,0.229 0.656,0.458 0.365,0.229 10 true SST

a.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07060)


Hide 35790 61.REMOVE 1-WAY CLUTCH ASSEMBLY

D027928

a.

Remove the 1-way clutch assembly and No. 1 planetary carrier thrust washer from the case.


Hide 35664 62.REMOVE 2ND BRAKE CYLINDER

D027929

a.

Remove the 2nd brake cylinder from the case.


Hide 35624 63.REMOVE 2ND BRAKE PISTON

D028817E08
2.219,0.552 2.74,0.219 2.74,0.219 2.813,0.219 true 2.875,0.125 3.229,0.302 0.354,0.177 10 false SST

a.

Using SST and a press, compress the return spring and remove the snap ring.

SST
09351-40010  


b.
D028545

Hold the 2nd brake cylinder and apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the 2nd brake cylinder to remove the 2nd brake piston.


c.
D028546

Remove the 2 O-rings from the 2nd brake piston.


Hide 35046 64.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35720 65.REMOVE FRONT PLANETARY GEAR ASSEMBLY

D027930

a.

Remove the 1-way clutch inner race and front planetary gear assembly from the case.


b.
D027931

Remove the thrust bearing race, thrust needle roller bearing and No. 2 planetary carrier thrust washer from the front planetary gear assembly.


Hide 68.REMOVE FRONT PLANETARY RING GEAR

D027932

a.

Remove the front planetary ring gear and thrust needle roller bearing from the transmission case.


Hide 35763 69.REMOVE CENTER PLANETARY RING GEAR

D028540

a.

Using a screwdriver, remove the snap ring.


b.
D028541

Remove the center planetary ring gear and front planetary ring gear flange from the front planetary ring gear.


Hide 35681A 70.REMOVE NO. 1 BRAKE DISC

a.

Remove the flange, 3 discs and 3 plates from the case.


Hide 35608K 72.REMOVE BRAKE PISTON RETURN SPRING SNAP RING

D027934

a.

Using a screwdriver, remove the brake piston return spring snap ring from the case.


Hide 35608J 73.REMOVE BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

D027935

a.

Remove the brake piston return spring and No. 1 brake piston with No. 1 brake cylinder from the transmission case.


Hide 35608J 74.INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35621V 75.REMOVE NO. 1 BRAKE PISTON

D027936

a.

Hold the No. 1 brake cylinder and apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the No. 1 brake cylinder to remove the No. 1 brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.

Remove the 2 O-rings from the No. 1 brake piston.


Hide 35682A 76.REMOVE NO. 2 BRAKE DISC

D027937

a.

Using a screwdriver, remove the snap ring from the case.


b.

Remove the flange, 3 discs, 3 plates and brake piston return spring from the case.


Hide 35045 78.INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35622G 79.REMOVE NO. 2 BRAKE PISTON

D027939

a.

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the transmission case to remove the No. 2 brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.

Remove the 2 O-rings from the No. 2 brake piston.


Hide 35750 80.REMOVE CENTER PLANETARY GEAR ASSEMBLY

D027940

a.

Remove the thrust bearing race, center planetary gear and planetary sun gear from the case.


Hide 35713 82.REMOVE INTERMEDIATE SHAFT

D027941

a.

Using a screwdriver, remove the snap ring from the case.


b.
D027942

Remove the intermediate shaft with No. 3 1-way clutch assembly from the case.


Hide 35770C 84.REMOVE NO. 3 1-WAY CLUTCH ASSEMBLY

D027964

a.

Remove the No. 3 1-way clutch assembly and 1-way clutch inner race from the intermediate shaft.


Hide 35077D 85.REMOVE REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

D027965

a.

Remove the planetary ring gear flange, 2 thrust bearing races and thrust needle roller bearing from the intermediate shaft.


Hide 35077D 86.INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

Hide 35639B 88.REMOVE BRAKE PLATE STOPPER SPRING

D027943

Hide 89.REMOVE NO. 4 BRAKE DISC

a.

Remove the 7 plates, 8 discs and 2 flanges from the case.


Hide 35719B 91.REMOVE REAR PLANETARY GEAR ASSEMBLY

C161737

a.

Remove the rear planetary gear assembly from the case.


b.
C161738

Remove the 2 thrust needle roller bearings from the rear planetary gear.


c.
U116383

Remove the thrust bearing race from the case.


Hide 35068 93.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

D028083E04
2.427,1.031 2.698,0.208 2.698,0.208 2.813,0.208 false 1.469,0.75 1.417,0.26 1.417,0.26 1.313,0.26 false 2.854,0.125 3.063,0.292 0.208,0.167 10 false *1 0.958,0.208 1.26,0.385 0.302,0.177 10 false SST

a.

Place SST on the spring retainer and compress the brake return spring.

SST
09350-30020  (09350-07050)

Text in Illustration
*1 Snap Ring


b.

Using SST, remove the snap ring and brake return spring.

SST
09350-30020  (09350-07070)


Hide 35068 94.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

Hide 35623H 95.REMOVE 1ST AND REVERSE BRAKE PISTON

D027948

a.

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the transmission case to remove the 1st and reverse brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.

Remove the O-ring from the 1st and reverse brake piston.


Hide 35626 96.REMOVE BRAKE REACTION SLEEVE

D028079E05
1.49,0.417 1.083,0.417 false 0.76,0.344 1.073,0.552 0.313,0.208 10 false SST

a.

Using SST, remove the reaction sleeve.

SST
09350-30020  (09350-07080)


b.

Remove the 2 O-rings from the reaction sleeve.


Hide 35629A 97.REMOVE NO. 4 BRAKE PISTON

D001240E04
1.26,0.313 1.563,0.542 false 0.917,0.177 1.313,0.385 0.396,0.208 10 false SST

a.

Using SST, remove the brake piston.

SST
09350-30020  (09350-07090)


b.

Remove the 2 O-rings from the brake piston.