Home › Drivetrain › A750E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM1440E _52 Drivetrain _056133 A750E AUTOMATIC TRANSMISSION / TRANSAXLE _0273938 AUTOMATIC TRANSMISSION SYSTEM C

A750E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0778  Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2)  


DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2 and SR, which are controlled by the ECM. If an open or short circuit occurs in one of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly (See page Drivetrain>A750E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART).

DTC Code DTC Detection Condition Trouble Area
P0778 The ECM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears (1-trip detection logic).
Output signal duty ratio equals 100%.
HINT:

SL2 output signal duty is less than 100% under normal conditions.


·

Open or short in shift solenoid valve SL2 circuit

·

Shift solenoid valve SL2

·

ECM



MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL2 circuit. The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. Then the ECM performs the fail-safe function and turns the other normal shift solenoid valves ON/OFF. In case of an open or short circuit, the ECM stops sending current to the circuit.

While driving and shifting gears, if the ECM detects an open or short in the shift solenoid valve SL2 circuit, the ECM determines there is a malfunction (See page Drivetrain>A750E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART).

WIRING DIAGRAM

C217168E12
2.813,1.323 3.042,1.49 0.229,0.167 10 false 11 5.427,1.042 5.656,1.208 0.229,0.167 10 false 31 2.813,2.531 3.042,2.698 0.229,0.167 10 false 3 2.323,2.333 2.75,2.531 0.427,0.198 10 false SL2- 5.75,1.208 6.177,1.406 0.427,0.198 10 false SL2+ 5.427,2.25 5.656,2.417 0.229,0.167 10 false 34 5.75,2.417 6.177,2.615 0.427,0.198 10 false SL2- 1.021,2.896 1.448,3.094 0.427,0.198 10 false B32 1.021,3.073 2.271,3.271 1.25,0.198 10 false Transmission Wire 1.042,1.76 2.688,1.99 1.646,0.229 10 false Shift Solenoid Valve SL2 5.958,3.219 6.385,3.417 0.427,0.198 10 false ECM 0.833,1.396 1.063,1.563 0.229,0.167 10 false 1 0.833,2.208 1.063,2.375 0.229,0.167 10 false 2 5.375,1.219 5.667,1.385 0.292,0.167 10 false B37 5.375,2.427 5.667,2.594 0.292,0.167 10 false B38 2.323,1.115 2.75,1.313 0.427,0.198 10 false SL2+

CAUTION / NOTICE / HINT

HINT:

The shift solenoid valve SL2 turns ON/OFF normally when the shift lever is in D.

ECM gear shift command 1st 2nd 3rd 4th 5th
Shift solenoid valve SL2 ON ON ON ON OFF


PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL2)
a.
C214326E03
1.868,1.306 1.669,1.745 false 1.941,1.087 2.195,1.745 false 1.432,1.783 1.795,1.950 0.363,0.167 10 SL2+ 0.055,0.021 0.279,0.187 0.224,0.167 10 *a 2.056,1.783 2.398,1.950 0.343,0.167 10 SL2-

Disconnect the B32 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
11 (SL2+) - 3 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
11 (SL2+) - Body ground Always 10 kΩ or higher
3 (SL2-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL2
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
U180921E02
1.833,2.771 2.094,2.219 false 2.49,2.771 2.229,2.219 false 0.052,0.031 0.302,0.229 0.25,0.198 10 false *a 1.823,0.396 2.198,0.625 0.375,0.229 10 false B37 1.396,2.802 2.042,3 0.646,0.198 10 false 31 (SL2+) 2.292,0.396 2.667,0.625 0.375,0.229 10 false B38 2.292,2.802 2.938,3 0.646,0.198 10 false 34 (SL2-)

Disconnect the B37 and B38 ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B37-31 (SL2+) - B38-34 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
B37-31 (SL2+) - Body ground Always 10 kΩ or higher
B38-34 (SL2-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR